Skip to content

Latest commit

 

History

History
138 lines (107 loc) · 6.27 KB

Ardulink2-Specification.md

File metadata and controls

138 lines (107 loc) · 6.27 KB
Raw

Protocol Specification: Ardulink Protocol (alp://)

Overview

This protocol enables communication between an Arduino device and a host system over serial communication. It allows the remote control of actuators and monitoring of sensors. Each command follows the format alp://<command>/<pin>/<value>, with an optional ?id=<id> that can be added to the message for tracking individual commands.

  • Note: The id=<id> parameter is optional in all commands. If included in the command, it will be included in the response. If no id is provided in the command, there will be no response.

Command Formats

1. Key Press (kprs)

  • Command: alp://kprs/<message>?id=<id> (Optional: ?id=<id>)
  • Description: Sent when a key is pressed.
  • Parameters:
    • message: The key press message (e.g., "a", "b", etc.).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

2. Power Pin Intensity (ppin)

  • Command: alp://ppin/<pin>/<intensity>?id=<id> (Optional: ?id=<id>)
  • Description: Set the intensity (PWM value) for a power pin.
  • Parameters:
    • pin: Pin number (integer).
    • intensity: PWM intensity value (0-255).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

3. Power Pin Switch (ppsw)

  • Command: alp://ppsw/<pin>/<power>?id=<id> (Optional: ?id=<id>)
  • Description: Set the power state of a pin (ON/OFF).
  • Parameters:
    • pin: Pin number (integer).
    • power: Power state (1 for ON, 0 for OFF).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

4. Tone Request (tone)

  • Command: alp://tone/<pin>/<frequency>/<duration>?id=<id> (Optional: ?id=<id>)
  • Description: Generate a tone on a specified pin.
  • Parameters:
    • pin: Pin number (integer).
    • frequency: Frequency of the tone (Hz).
    • duration: Duration of the tone in milliseconds. If -1, the tone will continue indefinitely.
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

5. No Tone Request (notn)

  • Command: alp://notn/<pin>?id=<id> (Optional: ?id=<id>)
  • Description: Stop the tone on a specified pin.
  • Parameters:
    • pin: Pin number (integer).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

6. Start Listen Digital Pin (srld)

  • Command: alp://srld/<pin>?id=<id> (Optional: ?id=<id>)
  • Description: Start listening to a digital pin for state changes.
  • Parameters:
    • pin: Pin number (integer).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

7. Stop Listen Digital Pin (spld)

  • Command: alp://spld/<pin>?id=<id> (Optional: ?id=<id>)
  • Description: Stop listening to a digital pin.
  • Parameters:
    • pin: Pin number (integer).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

8. Start Listen Analog Pin (srla)

  • Command: alp://srla/<pin>?id=<id> (Optional: ?id=<id>)
  • Description: Start listening to an analog pin for state changes.
  • Parameters:
    • pin: Pin number (integer).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

9. Stop Listen Analog Pin (spla)

  • Command: alp://spla/<pin>?id=<id> (Optional: ?id=<id>)
  • Description: Stop listening to an analog pin.
  • Parameters:
    • pin: Pin number (integer).
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

10. Custom Message (cust)

  • Command: alp://cust/<customId>/<value>?id=<id> (Optional: ?id=<id>)
  • Description: Send a custom message to the Arduino.
  • Parameters:
    • customId: Custom identifier for the message.
    • value: The custom message value.
    • id: (Optional) Unique message identifier. If provided, it will be included in the response.

Response Format

1. Reply (rply)

  • Command: alp://rply/<status>?id=<id>
  • Description: The Arduino sends a response back indicating the success or failure of the operation. The response includes the same id from the original command (if it was provided). If no id was provided in the the original command there will be no reply.
  • Parameters:
    • status: "ok" or "ko" indicating whether the command was successful or not.
    • id: The unique message identifier that was included in the original command.

2. Pin Reading

  • Command: alp://<type>/<pin>/<value>
  • Description: Sent when a pin's value is read (either digital or analog).
  • Parameters:
    • type: The type of pin ("dred" for digital or "ared" for analog).
    • pin: The pin number that is being monitored.
    • value: The value of the pin (either 0/1 for digital or an analog value).

Communication Flow

  1. Host to Arduino: The host system sends a command to the Arduino.
  2. Arduino Execution: The Arduino processes the command and interacts with the hardware as necessary.
  3. Arduino to Host: If the original command contained an id the Arduino sends a response with the requests' id same. If no id was provided in the command, the Arduino will not send a response for that command.

Example Communication

Case 1: Command with id

  1. Command: alp://srld/7?id=123

    • Description: Start listening to digital pin 7, with an id of "123".

  2. Arduino Response: alp://rply/ok?id=123

    • Description: Acknowledge the start of pin 7 listening, with the same id ("123") to match the original request.

Case 2: Command without id

  1. Command: alp://srld/7

    • Description: Start listening to digital pin 7, without an id.

  2. Arduino Response: (No response)

    • Description: Since the command did not include an id, no response is sent from the Arduino.

Key Points

  • id is optional in all commands.
  • If id is provided in the command, the Arduino includes the same id in the response.
  • If no id is included in the command, the Arduino does not send a response for that command.