ENGO EONE-230 help needed with certian parameters and behavoir

[PuckleGit]

Hello all, I'm currently creating a converter for the ENGO EONE-230 series of Zigbee thermostats that I've acquired recently for my home set-up. This is the product page of the device: https://engocontrols.com/en/produkt/eone-230w-3/

I've managed to hastily build a Tuya based converter (using the provided walk-through!) to handle many of the exposes and data-points that it utilises but have got some interesting parameters and would appreciate some input in how to handle them

Firstly, I've gotten the general climate exposes working with the exception of '.withLocalTemperature(ea.STATE)' which always gives an N/A value, however if I use 'e.temperature()' separately to the same data-point then it displays the temperature just fine

Secondly, this particular thermostat has some very modular settings as it can be used for a variety of heating or cooling applications. I've set up the general 'idle', 'heat' and 'cool' states as part of the Running state but the device technically has more than one idle state (one for 'heating off' and one for 'cooling off').

For context, the code list for the running state of the device contains these following states: [..."idle_sensor_error","heating","heating_off","cooling","cooling_off"...]. Regarding this is there a way to use the 'idle' state to be able to equal both heating off or cooling off?

[msiemienkowicz]

Hi, I'm struggling with the same thermostat, can you share your setup?

[PuckleGit]

Hi, I'm struggling with the same thermostat, can you share your setup?

Sure thing, sorry for the long delay. Here's the converter I made for my set-up a while ago. I still haven't managed to solve the original issues I had from above so it's written for heating only for now and the Local temperature still says N/A but everything else I've added appears to work.

I will advise against using the variables used for 'schedule_day' as I found that the converter only supports 4 state changes but the thermostat can support 6. If you change any of the schedule values it will end up putting them into values that are offset by 147 hours and put out of range, meaning you wont be able to change them back into range unless you factory reset the device

Not all of the datapoints are in the converter but I do have a complete list in a separate file I pulled from the TuYa IOT platform a while back if it's desired

const fz = require('zigbee-herdsman-converters/converters/fromZigbee');
const tz = require('zigbee-herdsman-converters/converters/toZigbee');
const exposes = require('zigbee-herdsman-converters/lib/exposes');
const reporting = require('zigbee-herdsman-converters/lib/reporting');
const modernExtend = require('zigbee-herdsman-converters/lib/modernExtend');
const e = exposes.presets;
const ea = exposes.access;
const tuya = require('zigbee-herdsman-converters/lib/tuya');

const definition = {
    // Since a lot of Tuya devices use the same modelID, but use different datapoints
    // it's necessary to provide a fingerprint instead of a zigbeeModel
    fingerprint: [
        {
            // The model ID from: Device with modelID 'TS0601' is not supported
            // You may need to add \u0000 at the end of the name in some cases
            modelID: 'TS0601',
            // The manufacturer name from: Device with modelID 'TS0601' is not supported.
            manufacturerName: '_TZE200_awnadkan',
        },
    ],
    model: 'WBONE230',
    vendor: 'Tuya',
    description: 'Zigbee Smart Thermostat',
    fromZigbee: [tuya.fz.datapoints],
    toZigbee: [tuya.tz.datapoints],
	whiteLabel: [tuya.whitelabel('ENGO', 'EONE-230', 'Zigbee Smart Thermostat', ['_TZE200_awnadkan'])],
    onEvent: tuya.onEventSetTime, // Add this if you are getting no converter for 'commandMcuSyncTime'
    configure: tuya.configureMagicPacket,
    exposes: [
		e.binary('state', ea.STATE_SET, 'ON', 'OFF').withDescription('Turn the thermostat ON/OFF'),
		e
			.climate()
			.withSystemMode(['heat', 'cool'], ea.STATE_SET)
			.withSetpoint('current_heating_setpoint', 5, 45, 0.5, ea.STATE_SET)
			.withLocalTemperature(ea.STATE)
			.withLocalTemperatureCalibration(-3.5, 3.5, 0.5, ea.STATE_SET)
			.withRunningState(['idle', 'heat', 'cool'], ea.STATE)
			.withPreset(['Manual', 'Program', 'Holiday', 'Temporary', 'OccupancyOff', 'Frost']),
		e.temperature(),
		e.humidity(),
		e.holiday_temperature().withValueMin(5).withValueMax(45),
		e
			.numeric('holiday_days', ea.STATE_SET)
			.withDescription('Set the number of days of holiday.')
			.withUnit('days')
			.withValueMin(1)
			.withValueMax(30),
		e
			.numeric('frost_set', ea.STATE_SET)
			.withDescription('Set the frost protection temperature.')
			.withUnit('°C')
			.withValueMin(5)
			.withValueMax(17)
			.withValueStep(0.5),
		...tuya.exposes.scheduleAllDays(ea.STATE_SET, 'HH:MM/C HH:MM/C HH:MM/C HH:MM/C HH:MM/C HH:MM/C'),
		e.enum('control_algorithm', ea.STATE_SET, ['TPI_UFH', 'TPI_RAD', 'TPI_ELE', 'HIS_02', 'HIS_04', 'HIS_06', 'HIS_08', 'HIS_10', 'HIS_20', 'HIS_30', 'HIS_40']).withDescription('Sets the control algorithim of the thermostat'),
		e.max_temperature().withValueMin(5).withValueMax(45),
		e.min_temperature().withValueMin(5).withValueMax(45),
		e.enum('sensor_choose', ea.STATE_SET, ['Internal', 'All', 'External', 'Occupancy']).withDescription('Sets the sensor mode of the thermostat'),
		//e.enum('sensor_error', ea.STATE, ['Normal', 'E1', 'E2']).withDescription('Shows the sensor status'),
		e.binary('valve_protection', ea.STATE_SET, 'ON', 'OFF').withDescription('Enable valve protection'),
		e.enum('relay_mode', ea.STATE_SET, ['NO', 'NC', 'OFF']).withDescription('Sets the internal relay function'),
		e
			.numeric('backlight', ea.STATE_SET)
			.withDescription('Set the backlight brightness of the thermostat.')
			.withUnit('%')
			.withValueMin(0)
			.withValueMax(100)
			.withValueStep(10),
		e.enum('temp_resolution', ea.STATE_SET, ['One', 'Five']).withDescription('Sets the temperature resolution, ±0.1 or ±0.5'),
		e.child_lock(),
	],
    meta: {
        // All datapoints go in here
        tuyaDatapoints:[
			[1, 'state', tuya.valueConverter.onOff],
			[
				2, 
				'system_mode', 
				tuya.valueConverterBasic.lookup({
					heat: tuya.enum(0),
					cool: tuya.enum(1)
				}),
			],
			[
				3, 
				'running_state', 
				tuya.valueConverterBasic.lookup({
					error: tuya.enum(0),
					heat: tuya.enum(1),
					idle: tuya.enum(2),
					cool: tuya.enum(3),
					defrost: tuya.enum(10),
					off: tuya.enum(11)
				}),
			],
			[16, 'current_cooling_setpoint', tuya.valueConverter.divideBy10],
			[16, 'current_heating_setpoint', tuya.valueConverter.divideBy10],
			[19, 'max_temperature', tuya.valueConverter.divideBy10],
			[24, 'temperature', tuya.valueConverter.divideBy10],
			[24, 'local_temperature', tuya.valueConverter.divideBy10],
			[27, 'local_temperature_calibration', tuya.valueConverter.divideBy10],
			[26, 'min_temperature', tuya.valueConverter.divideBy10],
			[32, 'holiday_temperature', tuya.valueConverter.divideBy10],
			[33, 'holiday_days', tuya.valueConverter.raw],
			[34, 'humidity', tuya.valueConverter.raw],
			[40, 'child_lock', tuya.valueConverter.lockUnlock],
			[
				43,
				'sensor_choose',
				tuya.valueConverterBasic.lookup({
					Internal: tuya.enum(0),
					All: tuya.enum(1),
					External: tuya.enum(2),
					Occupancy: tuya.enum(3)
				}),
			],
			[44, 'backlight', tuya.valueConverter.raw],
			[
				58, 
				'preset', 
				tuya.valueConverterBasic.lookup({
					Manual: tuya.enum(0),
					Program: tuya.enum(1),
					Holiday: tuya.enum(2),
					Temporary: tuya.enum(3),
					OccupancyOff: tuya.enum(4),
					Frost: tuya.enum(5)
				}),
			],
			[
				101,
				'control_algorithm',
				tuya.valueConverterBasic.lookup({
					TPI_UFH: tuya.enum(0),
					TPI_RAD: tuya.enum(1),
					TPI_ELE: tuya.enum(2),
					HIS_02: tuya.enum(3),
					HIS_04: tuya.enum(4),
					HIS_06: tuya.enum(5),
					HIS_08: tuya.enum(6),
					HIS_10: tuya.enum(7),
					HIS_20: tuya.enum(8),
					HIS_30: tuya.enum(9),
					HIS_40: tuya.enum(10)
				}),
			],
			[106, 'frost_set', tuya.valueConverter.divideBy10],
			[107, 'valve_protection', tuya.valueConverter.onOff],
			[
				108, 
				'relay_mode', 
				tuya.valueConverterBasic.lookup({
					NO: tuya.enum(0),
					NC: tuya.enum(1),
					OFF: tuya.enum(2)
				}),
			],
			[109, 'schedule_monday', tuya.valueConverter.thermostatScheduleDayMultiDPWithDayNumber(1)],
			[110, 'schedule_tuesday', tuya.valueConverter.thermostatScheduleDayMultiDPWithDayNumber(2)],
			[111, 'schedule_wednesday', tuya.valueConverter.thermostatScheduleDayMultiDPWithDayNumber(3)],
			[112, 'schedule_thursday', tuya.valueConverter.thermostatScheduleDayMultiDPWithDayNumber(4)],
			[113, 'schedule_friday', tuya.valueConverter.thermostatScheduleDayMultiDPWithDayNumber(5)],
			[114, 'schedule_saturday', tuya.valueConverter.thermostatScheduleDayMultiDPWithDayNumber(6)],
			[115, 'schedule_sunday', tuya.valueConverter.thermostatScheduleDayMultiDPWithDayNumber(7)],
			[
				117, 
				'temp_resolution',
				tuya.valueConverterBasic.lookup({
					One: tuya.enum(0),
					Five: tuya.enum(1)
				}),
			],
			[
				120,
				'sensor_error',
				tuya.valueConverterBasic.lookup({
					Normal: tuya.enum(0),
					E1: tuya.enum(1),
					E2: tuya.enum(2)
				}),
			],
		],
    },
    extend: [
        // A preferred new way of extending functionality.
    ],
};

module.exports = definition;