RFID_LCD_LED.ino

#include <Wire.h> 
#include <LiquidCrystal_I2C.h>
#include <EEPROM.h>     // We are going to read and write PICC's UIDs from/to EEPROM
#include <SPI.h>        // RC522 Module uses SPI protocol
#include <MFRC522.h>  // Library for Mifare RC522 Devices

LiquidCrystal_I2C lcd(0x27,16,2);
#define COMMON_ANODE
#define LED_ON HIGH
#define LED_OFF LOW
#define redLed 7    // Set Led Pins
#define greenLed 6
#define blueLed 5
#define relay 4     // Set Relay Pin
#define wipeB 3     // Button pin for WipeMode
bool programMode = false;  // initialize programming mode to false
uint8_t successRead;    // Variable integer to keep if we have Successful Read from Reader
byte storedCard[4];   // Stores an ID read from EEPROM
byte readCard[4];   // Stores scanned ID read from RFID Module
byte masterCard[4];   // Stores master card's ID read from EEPROM
#define SS_PIN 10
#define RST_PIN 9
MFRC522 mfrc522(SS_PIN, RST_PIN);

///////////////////////////////////////// Setup ///////////////////////////////////
void setup() {
  lcd.init();                      // initialize the lcd 
  lcd.init();
  // Print a message to the LCD.
  lcd.backlight();
  lcd.setCursor(0,0);
  lcd.print("Welcome!!");
  delay(1000);
  lcd.setCursor(0,1);
  lcd.print("Scan your card");
  delay(500);

  //Protocol Configuration
  Serial.begin(9600);  // Initialize serial communications with PC
  SPI.begin();           // MFRC522 Hardware uses SPI protocol
  mfrc522.PCD_Init();    // Initialize MFRC522 Hardware
if (EEPROM.read(1) != 143) {
    Serial.println(F("No Master Card Defined"));
    Serial.println(F("Scan A PICC to Define as Master Card"));
    do {
      successRead = getID();            // sets successRead to 1 when we get read from reader otherwise 0
      digitalWrite(blueLed, LED_ON);    // Visualize Master Card need to be defined
      delay(200);
      digitalWrite(blueLed, LED_OFF);
      delay(200);
    }
    while (!successRead);                  // Program will not go further while you not get a successful read
    for ( uint8_t j = 0; j < 4; j++ ) {        // Loop 4 times
      EEPROM.write( 2 + j, readCard[j] );  // Write scanned PICC's UID to EEPROM, start from address 3
    }
    EEPROM.write(1, 143);                  // Write to EEPROM we defined Master Card.
    Serial.println(F("Master Card Defined"));
  }
  Serial.println(F("-------------------"));
  Serial.println(F("Master Card's UID"));
  for ( uint8_t i = 0; i < 4; i++ ) {          // Read Master Card's UID from EEPROM
    masterCard[i] = EEPROM.read(2 + i);    // Write it to masterCard
    Serial.print(masterCard[i], HEX);
  }
  Serial.println("");
  Serial.println(F("-------------------"));
  Serial.println(F("Everything is ready"));
  Serial.println(F("Waiting PICCs to be scanned"));
}



///////////////////////////////////////// Main Loop ///////////////////////////////////
void loop () {
  while (!successRead);   //the program will not go further while you are not getting a successful read
    if ( isMaster(readCard)) {    // If scanned card's ID matches Master Card's ID - enter program mode
      programMode = true;
      Serial.println(F("Hello Master - Entered Program Mode"));
    lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("Hello Master");
    lcd.setCursor(0,1);
    lcd.print("> Program Mode <");
      uint8_t count = EEPROM.read(0);   // Read the first Byte of EEPROM that
      Serial.print(F("I have "));     // stores the number of ID's in EEPROM
      Serial.print(count);
      Serial.print(F(" record(s) on EEPROM"));
      Serial.println("");
      Serial.println(F("Scan a PICC to ADD or REMOVE to EEPROM"));
      Serial.println(F("Scan Master Card again to Exit Program Mode"));
      Serial.println(F("-----------------------------"));

    }
    else {
      if ( findID(readCard) ) { // If not, see if the card is in the EEPROM
        Serial.println(F("Welcome, Master"));
            lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("Welcome home!");
    lcd.setCursor(0,1);
    lcd.print("Master X");
        granted(300);         // Open the door lock for 300 ms
      }
      else {      // If not, show that the ID was not valid
        Serial.println(F("You shall not pass"));
         lcd.clear();
    lcd.setCursor(0,0);
    lcd.print("Sorry! You don't");
    lcd.setCursor(0,1);
    lcd.print("have access.");
        denied();
      }
    }
  }

/////////////////////////////////////////  Access Granted    ///////////////////////////////////
void granted ( uint16_t setDelay) {
  digitalWrite(blueLed, LED_OFF);   // Turn off blue LED
  digitalWrite(redLed, LED_OFF);  // Turn off red LED
  digitalWrite(greenLed, LED_ON);   // Turn on green LED
  digitalWrite(relay, LOW);     // Unlock door!
  delay(setDelay);          // Hold door lock open for given seconds
  digitalWrite(relay, HIGH);    // Relock door
  delay(1000);            // Hold green LED on for a second
}

///////////////////////////////////////// Access Denied  ///////////////////////////////////
void denied() {
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  digitalWrite(redLed, LED_ON);   // Turn on red LED
  delay(1000);
}


///////////////////////////////////////// Get PICC's UID ///////////////////////////////////
uint8_t getID() {
  // Getting ready for Reading PICCs
  if ( ! mfrc522.PICC_IsNewCardPresent()) { //If a new PICC placed to RFID reader continue
    return 0;
  }
  if ( ! mfrc522.PICC_ReadCardSerial()) {   //Since a PICC placed get Serial and continue
    return 0;
  }
  // There are Mifare PICCs which have 4 byte or 7 byte UID care if you use 7 byte PICC
  // I think we should assume every PICC as they have 4 byte UID
  // Until we support 7 byte PICCs
  Serial.println(F("Scanned PICC's UID:"));
  for ( uint8_t i = 0; i < 4; i++) {  //
    readCard[i] = mfrc522.uid.uidByte[i];
    Serial.print(readCard[i], HEX);
  }
  Serial.println("");
  mfrc522.PICC_HaltA(); // Stop reading
  return 1;
}

void ShowReaderDetails() {
  // Get the MFRC522 software version
  byte v = mfrc522.PCD_ReadRegister(mfrc522.VersionReg);
  Serial.print(F("MFRC522 Software Version: 0x"));
  Serial.print(v, HEX);
  if (v == 0x91)
    Serial.print(F(" = v1.0"));
  else if (v == 0x92)
    Serial.print(F(" = v2.0"));
  else
    Serial.print(F(" (unknown),probably a chinese clone?"));
  Serial.println("");
  // When 0x00 or 0xFF is returned, communication probably failed
  if ((v == 0x00) || (v == 0xFF)) {
    Serial.println(F("WARNING: Communication failure, is the MFRC522 properly connected?"));
    Serial.println(F("SYSTEM HALTED: Check connections."));
    // Visualize system is halted
    digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
    digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
    digitalWrite(redLed, LED_ON);   // Turn on red LED
    while (true); // do not go further
  }
}

//////////////////////////////////////// Read an ID from EEPROM //////////////////////////////
void readID( uint8_t number ) {
  uint8_t start = (number * 4 ) + 2;    // Figure out starting position
  for ( uint8_t i = 0; i < 4; i++ ) {     // Loop 4 times to get the 4 Bytes
    storedCard[i] = EEPROM.read(start + i);   // Assign values read from EEPROM to array
  }
}

///////////////////////////////////////// Check Bytes   ///////////////////////////////////
bool checkTwo ( byte a[], byte b[] ) {   
  for ( uint8_t k = 0; k < 4; k++ ) {   // Loop 4 times
    if ( a[k] != b[k] ) {     // IF a != b then false, because: one fails, all fail
       return false;
    }
  }
  return true;  
}

///////////////////////////////////////// Find Slot   ///////////////////////////////////
uint8_t findIDSLOT( byte find[] ) {
  uint8_t count = EEPROM.read(0);       // Read the first Byte of EEPROM that
  for ( uint8_t i = 1; i <= count; i++ ) {    // Loop once for each EEPROM entry
    readID(i);                // Read an ID from EEPROM, it is stored in storedCard[4]
    if ( checkTwo( find, storedCard ) ) {   // Check to see if the storedCard read from EEPROM
      // is the same as the find[] ID card passed
      return i;         // The slot number of the card
    }
  }
}

///////////////////////////////////////// Find ID From EEPROM   ///////////////////////////////////
bool findID( byte find[] ) {
  uint8_t count = EEPROM.read(0);     // Read the first Byte of EEPROM that
  for ( uint8_t i = 1; i < count; i++ ) {    // Loop once for each EEPROM entry
    readID(i);          // Read an ID from EEPROM, it is stored in storedCard[4]
    if ( checkTwo( find, storedCard ) ) {   // Check to see if the storedCard read from EEPROM
      return true;
    }
    else {    // If not, return false
    }
  }
  return false;
}

///////////////////////////////////////// Write Success to EEPROM   ///////////////////////////////////
// Flashes the green LED 3 times to indicate a successful write to EEPROM
void successWrite() {
  digitalWrite(blueLed, LED_OFF);   // Make sure blue LED is off
  digitalWrite(redLed, LED_OFF);  // Make sure red LED is off
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is on
  delay(200);
  digitalWrite(greenLed, LED_ON);   // Make sure green LED is on
  delay(200);
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  delay(200);
  digitalWrite(greenLed, LED_ON);   // Make sure green LED is on
  delay(200);
  digitalWrite(greenLed, LED_OFF);  // Make sure green LED is off
  delay(200);
  digitalWrite(greenLed, LED_ON);   // Make sure green LED is on
  delay(200);
}

////////////////////// Check readCard IF is masterCard   ///////////////////////////////////
// Check to see if the ID passed is the master programing card
bool isMaster( byte test[] ) {
	return checkTwo(test, masterCard);
}

bool monitorWipeButton(uint32_t interval) {
  uint32_t now = (uint32_t)millis();
  while ((uint32_t)millis() - now < interval)  {
    // check on every half a second
    if (((uint32_t)millis() % 500) == 0) {
      if (digitalRead(wipeB) != LOW)
        return false;
    }
  }
  return true;
}