-
-
Notifications
You must be signed in to change notification settings - Fork 504
Compatible devices
Andreas Schildbach edited this page Sep 27, 2019
·
275 revisions
The following devices are produced by Tuya and can be flashed with third-party firmware. It is recommended that you make a backup of the factory firmware in the event that you need to revert to it should the third-party firmware not function properly with your device.
Since Sonoff-Tasmota version 6.4.1.16, the firmware supports templates for configuring unsupported devices. With version 6.4.1.17 templates are easily configurable in the web UI. It is recommended to use templates instead of changing Generic Module (18) GPIO assignments. The Tasmota wiki has started maintaining a list of user created templates. There are numerous devices based on Tuya Wi-Fi modules. It may not be possible for all of them to work as expected with Tasmota. If you have a new device that does not have an existing module/template, you may refer to this guide to configure the device.
| Vendor | Area | Device Name | Vendors device ID | GPIOs | Notes | 2nd MCU | Flash size/mode |
|---|---|---|---|---|---|---|---|
| 3stone | US | Smart Plug Mini | XS-SSA01 | pin 1: button (low=pressed) pin 13: LED (low=on) pin 14: relay (high=closed) |
flash chip seems pretty fast is ETL listed, despite no ETL logo on the device |
? | 1M QIO |
| ablue | EU | Smart Plug | SP1 | ? | ? | ? | ? |
| Aicliv | US | Outdoor Smart Socket | AS2100 | GPIO3: Relay3, GPIO4: Led2, GPIO12: Relay1, GPIO13: Button2, GPIO14: Relay2 | Tasmota Generic | 1M DOUT @ 40MHz | |
| AISIRER | EU | Smart Plug | AWP07L | ? | works with Tasmota profile #45 (Blitzwolf) | 1M DOUT @ 40MHz | |
| Aicliv | US | Outdoor Smart Socket | AS2100 | GPIO3: Relay3, GPIO4: Led2, GPIO12: Relay1, GPIO13: Button2, GPIO14: Relay2 | Tasmota Generic | 1M DOUT @ 40MHz | |
| Albohes | US | Outdoor Smart Socket Dual | PS-1602 | GPIO0: Button1, GPIO5: Relay2, GPIO9: Button2, GPIO12: Relay1 | Tasmota Generic | ? | ? |
| Aneken | US | Smart Socket | SWA5 | GPIO15: Relay1, GPIO13: Button1, GPIO2: LED1i | Tasmota Generic | 1M DOUT | |
| ANIKUV | US | Mini Smart Outlet | YM-WS-1 | GPIO12: LED1i GPIO13: Button1 GPIO15: Relay1 | Wifi-Smart-Plug-ANIKUV-Outlet Works with Tasmota Generic Module | ? | 1M DOUT |
| Aplic / CSL | EU | Wifi Smart Socket | WDP 303075 | ? | Tasmota Profile 53 | 1M DOUT @ 40 MHz | |
| Avatar Controls | EU | Mini Smart Wifi Plug | AWP07L | ? | ? | ? | ? |
| Avatar Controls | EU | Mini Smart Wifi Plug | AWP08L | GPIO03: Led1i, GPIO13: Button1, GPIO15: Relay1 | ? | ? | 1M DOUT @ 40MHz |
| Bestek | US | Smart Plug | MJR1011 | GPIO4 = led1i(56) GPIO12 = Relay1(21) GPIO13 = Button1(17) | Tasmota Generic | 1M DOUT @ 40MHz | |
| BlitzWolf | EU | Smart Socket | BW-SHP2 | ? | Device profile already included in Tasmota | N | 1M DOUT |
| BlitzWolf | US | Smart Socket | BW-SHP3 | ? | Tasmota Template | N | 1M DOUT |
| BlitzWolf | EU | Smart Socket | BW-SHP6 | ? | Identical to BlitzWolf BW-SHP2 | N | ? |
| Blue Shark | US | Blue Shark Wifi Mini Plug | W-US003, MPV2RQ-US | pin 0 = blue LED (low=on), pin 13 = button (low = pressed), pin 15 = relay (high = on) | cheapest US outlet on amazon march 2019, WARNING: not UL/ETL listed! one of mine registers as "hot ground" and "open neutral" with my outlet tester! DO NOT BUY, UNSAFE | ? | 1M DOUT |
| Brilliant | AU | Smart Wifi Plug and USB Charger | 20676/05 | GPIO05: Relay1, GPIO14: Button1 | Tasmota Generic. New devices have the patched firmware and will not convert OTA | ? | 1M DOUT |
| cDream | EU | Smart WLAN Socket | NX-SM200 | GPIO4: Led1, GPIO5: BL0937 CF, GPIO12: HLWBL SELi, GPIO13: Button1, GPIO14: HLWBL CF1, GPIO15: Relay1 | Template | ? | 1M DOUT @ 40MHz |
| Coosa | EU | WiFi Smart Socket | ? | GPIO4: LED2, GPIO5: LED1i, GPIO12:Relais 1, GPIO13:Button 1 | Tasmota Generic | ? | 1M DOUT |
| Epicka | US | Smart Plug | WP1000 | GPIO4=LED1i(Blue), GPIO5=LED2i(Red), GPIO12=Relay1, GPIO13=Button1 | Tasmota Generic | ||
| Etlephe | EU | Powerstrip | ? | GPIO3=LED1i, GPIO4=Relay 4i, GPIO5=Button1, GPIO12=Relay2i, GPIO13=Relay3i, GPIO14=Relay1i, GPIO16=Relay5 | ? | ? | ? |
| EVA LOGIK | US | Mini Smart Plug | NWF001 | GPIO1: Button1, GPIO13: Led1, GPIO14:Relay1 | |||
| GDTech | US | WiFi Mini Plug | MPV2RO-US | GPIO1: Button1 (Inverted), GPIO13: LED1 (Inverted), GPIO14: Relay1 | ? | ? | 1M DOUT |
| Geekbes | US | Mini Smart Socket | YM-WS-1 | GPIO1: Button1, GPIO13: LED1, GPIO14: Relay1 | Works with Tasmota Generic Module | ? | 1M ??? |
| Globe | CA | Smart Plug | 50000 | ?? | Tasmota Generic | ||
| Gosund | EU | Smart Plug | SP111 | ? | works with Tasmota profile #45 (BlitzWolf SHP2)
|
? | 1M DOUT |
| Gosund | EU | Smart Plug | SP1 (2200W/10A) | GPIO02: BLUE, GPIO05: CF PIN, GPIO12: SEL PIN, GPIO13: Button1, GPIO14: CF1 PIN, GPIO15: Relay | ? | ? | ? |
| Gosund | EU | Smart Plug | SP1 | GPIO1: Blue LED, GPIO13: Red LED, GPIO14: Relay, GPIO3: Button, GPIO4&5: hlw8012 | - | ? | 1M DOUT @ 40mhz (ESP8285) |
| Gosund | US | Smart Plug | WP3 | Template | - | ? | ? |
| Gosund | US | Smart Plug | WP5 | GPIO4: Switch1, GPIO12: LED2i, GPIO13: LED1i, GPIO14: Relay1 If this configuration doesn't work, try the Tecking SP10 Configuration below. |
Switch1 / Button1 are interchangeable. In an arduino sketch, use pins 4, 12, 13, and 14. | ? | 1M DOUT @ 40mhz (ESP8285) |
| Hama | EU | WLAN-/Smart Home Steckdose | 176533 | GPIO12 = Relay1, GPIO13 = Button1 | - | ? | ? |
| HoveBeaty | US | WiFi Smart Outlet | SM-PW701U | GPIO2=LED1i(bright blue), GPIO4=LED2i(dim blue), GPIO12=Relay1, GPIO13=Button1, Red LED tied to relay (no GPIO control) | Tasmota Generic | ||
| HugoAI | US | Mini Smart Socket | AWP02L-N | GPIO0 = LED2i, GPIO2 = LED1i, GPIO13 = Button1, GPIO15 = Relay1 | Tasmota Generic Module | ? | 1M DOUT |
| Hyleton 313 | UK | wifi smart plug | HLT-313 | GPIO0 = LED2i, GPIO2 = LED1i,GPIO13 = Button1,GPIO15 = Relay1 | - | ? | ? |
| Hyleton 314 | EU | wifi smart plug | HLT-314 | GPIO0 = LED2i, GPIO2 = LED1i,GPIO13 = Button1,GPIO15 = Relay1 | LEDs do not show state of relais | ? | 1M QIO |
| Hyleton 336 | UK | wifi smart power strip | HLT-336 | GPIO0 = LED1, GPIO3 = LED2i, GPIO4 = Relay1i, GPIO5 = Button1, GPIO12 = Relay3i, GPIO13 = Relay2i, GPIO16 = Relay4i | https://blakadder.github.io/templates/hyleton_336.html | ? | 1M QIO |
| Joywell | EU | 4-Plug-Multi-Socket (Type F) | ? | -- | clearly Tuya, but c't-sample was destroyed when tested, so no GPIOs yet. Hard to flash via serial due to GPIO 0 being on the back of the module (blocked by relay) | N | |
| Joinrun | EU | Smart Socket | W-DEXI | GPIO1: Button1n GPIO13: Led1 GPIO14: Relay1 | ? | ? | ? |
| KMC | US | 4 Outlet WiFi | KT-KMC | GPIO 13 Relay 2, GPIO 14 Relay 3, GPIO 15 Relay 1, GPIO 16 Button | ? | ? | ? |
| Kogan | AU | Wifi Smart Plug and power meter | - | GPIO0 (inverted) ( in some versions normal) Switch button, GPIO14 Relay, GPIO13 (inverted) Status led, hlw8012 power meter: GPIO12 sel pin (inverted), GPIO4 CF pin, GPIO5 CF1 pin | Used Tasmota Generic to flash Esphome | ? | 1M QIO @ 40MHz |
| Koogeek | EU | KLOE4 Smart Power Strip | KLOE4 | GPIO01 = LED1, GPIO3 = Button1, GPIO4 = Relay2, GPIO5 = Relay1, GPIO12 = Relay3, GPIO13 = Relay4, GPIO14 = Relay5 | works with the latest Espurna 1.13.3, build flag ZHILDE_EU44_W, or the precompiled binary espurna-1.13.3-zhilde-eu44-w.bin | ? | ? |
| Koogeek | UK | KLUP1 Wifi Smart Plug with energy monitoring | KLUP1 | ?? | Template | ? | |
| Lingan | EU | SWA1 | -- | GPIO 4 = LED, GPIO 5 = Relay, GPIO 13 = Button | -- | N | 1M QIO |
| Luntak | US | Wifi Smart Plug | -- | GPIO02 = LED GPIO13 = Button GPIO15 = Relay | Tasmota Generic | ? | ? |
| MartinJerry | US | mini Smart Plug | -- | GPIO04 = Led1i GPIO12 = Relay1 GPIO13 = Button1 | Tasmota Generic | ? | ? |
| Maxcio | EU | Wifi Smart Socket | W-DE004 | GPIO1 = Button1 GPIO13 = Led1i GPIO14 = Relay1 | Tasmota Generic | N | 1M QIO @40MHz |
| Maxcio | UK | Wifi Smart Plug w/ Energy Monitoring | W-UK007 | GPIO0=Led1i, GPIO13=Button1, GPIO15=Relay1 | Relay & power monitoring works with BlitzWolf SHP profile, but not LED (as GPIO0=Led2i) | ? | ? |
| Mengonee | EU | Wifi smart plug mini | JHG01E | GPIO4=LED1i, GPIO12=Relay1, GPIO13=Button1 | - | ? | 1MB DOUT |
| Merkury | CA,US | Indoor Wifi Smart Plug | MI-WW105 | GPIO4=LED2, GPIO5=LED1i, GPIO12=Relay1, GPIO13=Button1 | - | ? | 1M DOUT @ 40MHz |
| Merkury | US | Outdoor Wifi Smart Plug | MI-OW101-101W | GPIO0 = Button1, GPIO5=LED1i, GPIO13=LED2, GPIO14=Relay1 | Same As Geeni GN-OW101-101 | ? | 1M QIO |
| micmi | CA | WiFi Plug | sm-pw702 | GPIO12=Relay1, GPIO13=Button1,GPIO4 Blue LED | Orange LED follows relay | ? | 1M |
| Mirabella | AU | WiFi Power Plug with USB Port | I002341 | ? | ? | https://mirabellagenio.net.au/ | ? |
| MoesHouse | EU | Wifi Plug | ? | GPIO5 = Led1i, GPIO12 = Relay | - | ? | ? |
| Omoton | US | Wifi Smart Socket | W-US002 | GPIO1 = Button1, GPIO13 = Led1, GPIO14 = Relay1 | - | ? | ? |
| Panamalar | EU | Smart WLAN Socket | NX-SM200 | GPIO4: Led1, GPIO5: BL0937 CF, GPIO12: HLWBL SELi, GPIO13: Button1, GPIO14: NLWBL CF1, GPIO15: Relay1 | - | ? | 1M DOUT @ 40MHz |
| Rockbirds | US | Wifi Smart Plug | ? | GPIO2 = Led1, GPIO12 = Relay1, GPIO13 = Button1 | ? | 1M QIO | |
| TECKIN | US | Smart Plug with Power Monitoring | SP10 | GPIO0 = Led2i, GPIO2 = Led1i, GPIO13 = Button1, GPIO15 = Relay1 | ? | ? | |
| TECKIN | CA | Smart Plug with Power Monitoring | SP20 | ? | Tasmota 59 (Teckin US) | ? | 1M DOUT @ 40MHz |
| TECKIN | EU | Smart Plug | SP21 | ? | works with Tasmota profile #45 (BlitzWolf SHP2)
|
? | 1M DOUT |
| TECKIN | EU | WLAN Smart Steckdose | SP22 | GPIO1: Button1, GPIO3: Led2i (red), GPIO13: Led1i (blue), GPIO14: Relay1 | Tasmota Teckin preset works | ? | 1M DOUT @ 40MHz |
| TECKIN | EU | Smart Plug with Energy Monitoring | SP23 (UK) | GPIO15 = Relay, GPIO02 = Blue LED, GPIO05 = CF / Power, GPIO14 = CF1 / Current/Voltage, GPIO12 = Sel, GPIO13 = Button | Works with Tasmota profile #45 (BlitzWolf SHP2), ESPHome Example
|
? | ? |
| TECKIN | US | Smart Plug | SP25 | GPIO0 = Led1i, GPIO12 = Relay2, GPIO13 = Button1, GPIO15 = Relay1 | USB Power is Relay2 | 1M | |
| Tellur | EU | Powerstrip | TLL331031 | ? | works with Tasmota profile #60 (Manzoku strip)
|
? | ? |
| Tflag | EU | Smart Plug with Power Monitoring | NX-SM100 | GPIO0=56, GPIO5=134, GPIO12=21,GPIO13=17,GPIO14=132, GPIO15=57, GPIO16=131 | Works with Tasmota template (Nanxin NX-SM200) | ? | ? |
| Shenzhen Jiuheng | US | Smart Plug | JH-G01U | GPIO4 = Led1i, GPIO12 = Relay1, GPIO13 = Button1 | ? | ? | |
| Unknown | EU | Smart Wifi Power Strip (UK) | XS-A25 | GPIO0 = Led1, GPIO2 = Led2, GPIO4 = Relay5, GPIO5 = Relay2, GPIO12 = Relay4, GPIO13 = Button1, GPIO14 = Relay3, GPIO15 = Relay1 | Tasmota template: https://blakadder.github.io/templates/XS-A25.html | ? | 1M QIO |
| Unknown | EU | Wifi Smart Plug | BSD23 | GPIO4 = Led1, GPIO12 = Relay1, GPIO13 = Button1 | - | ? | 1M QIO |
| Unknown | EU | Wifi Smart Plug | BSD29 (UK) | GPIO3 = HLWBL SELi,GPIO4 = BL0937 CF,GPIO5 = HLWBL CF1,GPIO12 = Relay1, GPIO13 = Button1,GPIO14 = LED1i | Tasmota Template https://blakadder.github.io/templates/bsd29.html | ? | 1M DOUT |
| Unknown | UK | Power Work Google Plug | SWA9 | GPIO4 = LED1,GPIO5 = Relay1,GPIO13 = Button1 | Tasmota Template https://blakadder.github.io/templates/SWA9.html | ? | 1M DOUT |
| Unknown | US | Wi-Fi Smart Plug | X6 | GPIO0 = LED2i, GPIO2 = LED1i, GPIO13 = Button1, GPIO15 = Relay1 | No Manufacturer Information on Plug. Used Tasmota Generic Module | ? | 1M QIO |
| Unknown | US | Smart-Plug | YX-WS01 | GPIO1 = Switch1, GPIO13 = Led1i, Gpio14 = Relay1 | ? | ? | |
| JOMARTO | EU | Mini Smart WiFi Plug | ? | GPIO2=LED1, GPIO13=Button1, GPIO15=Relay1 | - | ? | ? |
| WAZA | EU | Wi-Fi Smart Plug | JH-G01E | GPIO4=Relay1, GPIO5=Button1, GPIO12=LED1i | - | ? | ? |
| Woox | EU | Smart Power Strip EU Type 16A 3 Ports | R4028 | GPIO1 = LED, GPIO3 = Button2, GPIO4 = Relay3 GPIO5 = Relay2, GPIO13 = Relay4, GPIO14 = Relay1 | -- | ? | 1M DOUT |
| Zhilde | EU | Smart-Power-Strip | ZLD-44EU-W | GPIO01 = LED1, GPIO3 = Button1, GPIO4 = Relay2, GPIO5 = Relay1, GPIO12 = Relay3, GPIO13 = Relay4, GPIO14 = Relay5 | works with the latest Espurna 1.13.3, build flag ZHILDE_EU44_W, or the precompiled binary espurna-1.13.3-zhilde-eu44-w.bin | ? | ? |
| ZOOZEE | US | Smart Plug | SA101 | GPIO0: LED2i-Red, GPIO2: Led1i-Blue, GPIO13: Button1, GPIO15: Relay1 | Tasmota Generic | ? | 1M DOUT |
| ZOOZEE (Wide Plug) | US | Smart Plug with monitoring | SA102 | ? | Teckin US preset works May need to configure in Smart Life, then use factory reset option before it can be flashed. |
? | 1M DOUT |
| ZOOZEE | EU | Smart Plug | SE131 | Tasmota Generic | Template: https://blakadder.github.io/templates/zoozee_SE131.html | 1M DOUT | |
| KING-LINK | US | OutDoor Smart Plug | C128 | GPIO04: Relay2, GPIO12: Relay1, GPIO14: Button1, GPIO15: Relay3, GPIO16: Led1i | Generic Config | ? | 1M QIO |
| Slitinto | EU | WiFi Smart Plug | NX-SP202 | GPIO12: Relay1, GPIO15: Relay2, The rest: ? | Generic Config | ? | ? |
| Yeron | US | Wifi Smart Plug with Power Monitoring | US101 | GPIO03: Button1, GPI04: HLW812 CF, GPIO5: HLWBL CF1, GPIO12: HLWBL SELi, GPIO13: LED1i, GPIO14: Relay1 | Generic Module - Developer Branch Tasmota 02052019 *1 of 2 units purchased March 4, 2018 never even tried to connect to the VTRUST network (that unit works with Smart Life, so not defective) |
? | |
| Slitinto | US | WiFi Dual Smart Plug with Power Monitoring | NX-SP201 | GPIO0: Led1i, GPIO4: Button1, GPIO5: HLW8012 CF, GPIO12: Relay1, GPIO13: Button2, GPIO14: HLWBL CF1, GPIO15: Relay2, GPIO16 HLWBL SEL | Generic Module - Developer Branch Tasmota 02052019 | ? | |
| Pearl | EU | Luminea Home Control WLAN Steckdose aussen | SF-550.avs | ? | Luminea ZX2820 - Developer Branch 6.4.1.14 including power monitoring; also KMC 70011 template but without correct power monitoring | ? | 1M QIO @ 40MHz |
| Pearl | EU | Luminea Home Control Touch-Lichtschalter | LHC-101.on | 0: Led2; 3: Button1; 4: Relay1; 14: Led1 | {"NAME":"LHC-101.on","GPIO":[53,0,0,17,21,0,0,0,0,0,52,0,0],"FLAG":0,"BASE":1} | ? | ? |
| Pearl | EU | Luminea Home Control WLAN Steckdose | SF-450.avs SF-500.avs | Blitzwolf Profile works | Luminea 450 without powermonitor | ? | ? |
| Neo Coolcam 10A | EU | Smart Plug 2000W/10A | WR01W | GPIO13: Button1, GPIO04: Led1, GPIO12: Relay1 | Sonoff Classic 6.4.1.15 / Generic Module. | ? | ? |
| Neo Coolcam 16A | EU | Smart Plug 3680W/16A with power monitoring | ? | GPIO0: Button1 (17), GPIO04: HWL8012 CF (133), GPIO05: HWLBL CF1 (132), GPIO12: HWLBL SELi(132), GPIO13: Led1i (56), GPIO14: Relay1 (21) | Sonoff Classic 6.4.1.15 / Generic Module. Works also on KMC70011, only w/o power monitoring. | ? | 499kB |
| ANCCY | EU | Smart Socket with power monitoring | SP1 | GPIO1: Led1i, GPIO3: Button1, GPIO4: HLW8012 CF, GPIO5: HLWBL CF1, GPIO12: HLWBL SELi, GPIO13: Led2i, GPIO14: Relay1 | Sonoff-sensors | 1M | |
| Oittm | CA/US | Outdoor Smart Socket with power monitoring | Smart-Plug-Outdoor | USE SK03 outdoor module | |||
| PRIME Cable | CA/US | CCRCWFIO2PK | Sold by Costco in canada | GPIO4: LED2 (53), GPIO5: Led1i (56), GPIO12: Button1 (21), GPIO135: Button1 (17) | This item was sold in Costco Wharehouse in canada only, did not find any online reference | - | - |
| Costco/CE | CA/US | CE smart Home LA-WF3 | Wi-Fi Smart Plug | GPIO4: Led1i (56), GPI05: Led2i (57), GPI12: Relay1 (21), GPI13: Button1 (17) | |||
| OxaOxe | US | Wi-Fi Smart Plug with Energy Monitor & Overload Protection | NX-SM800/NX-SP201 | Module 18; gpio0 57; gpio12 21; gpio13 17; gpio15 52; gpio4 131; gpio5 134; gpio14 132 | |||
| OxaOxe | EU | Wi-Fi Smart Plug with Energy Monitor | NX-SM200 | Module 18; gpio0 57; gpio12 21; gpio13 17; gpio15 52; gpio4 131; gpio5 134; gpio14 132 | |||
| Vansware Smart Plug 16A | EU | Wi-Fi Smart Plug with Energy Monitor | - | GPIO0: Button1 (17), GPIO04: HWL8012 CF (133), GPIO05: HWLBL CF1 (132), GPIO12: HWLBL SELi(132), GPIO13: Led1i (56), GPIO14: Relay1 (21) | Sonoff Classic 6.4.1.15 / Generic Module | - | - |
| Heygo 02 | US | Wi-Fi Smart Plug with Energy Monitor | - | ? | Espurna 1.13.5 HY02 | - | 1M DOUT |
| Hauppauge | EU | mySmarthome Voice Plug | SL-1642 | GPIO4: Led1, GPIO12: Relay1, GPIO12: Button 1 | Red LED is controlled by Relay1 | 1M QIO @ 40MHz | |
| BN-LINK | US | Smart WiFi Outlet, Hubless with Energy Monitoring and Timer Function | Smart-Plug | GPIO2: Led1i, GPIO3: Button1, GPIO13: Led2i, GPIO14: Relay1 | |||
| VIGICA 2.1A USB Charger 13A WiFi Wall Socket Smart Switch | UK | Wall outlet with 2 sockets and 2 USB chargers | Wall outlet | GPIO0: Button 1; GPIO5: Relay 2; GPIO9: Button 2; GPIO12: Relay 1 | |||
| GREFIC | EU | Mini Smart Plug | Gd003100 | GPIO4 = Relay1, GPIO5 = Button1, GPIO12 = Led1i | All is working | Tasmota generic (18) | 1M QIO @40MHz |
| Woox | EU | Smart Plug | R5024 | GPIO15: Relay, GPIO2: Led, GPIO13: Button | |||
| ZEOOTA | EU | Smart Power Strip | Tasmota Generic (18) | GPIO1: Led1i, GPIO3: Button 1 (17), GPIO4: Relay2 (22), GPIO5: Relay1 (21) GPIO12: Relay3 (23) GPIO13: Relay4 (24) GPIO14: Relay5 (25) | Can be bought on AliExpress, works well with default Tasmota included in the package. | ? | ? |
| Vendor | Socket-Type | Device Name | Vendors device ID | GPIOs | Notes | 2nd MCU | Flash size/mode |
|---|---|---|---|---|---|---|---|
| ASZKJ | E27 | Smart Bulb LED Wifi | SB001 | Red: GPIO14, Green: GPIO12, Blue:GPIO13, White: GPIO4 | Firmware updated already out the box | 1M QIO | |
| Blitzwolf | LED strip | Smart LED Light Strip | BW-LT11 | GPIO0: Button1,GPIO4: PWM1, GPIO5: PWM4, GPIO12: PWM2, GPIO14: PWM3 | US plug is also available. https://blakadder.github.io/templates/blitzwolf-bw-lt11.html | ? | |
| FCMILA | B22 | Generic Dimmable RGBW 7W LED (Cold White) | TYWE3S | GPIO5:PWM1=White, GPIO4:PWM2=Red, GPIO12:PWM3=Green, GPIO14:PWM4=Blue | Used git clone -b enhance-api https://github.com/kueblc/tuya-convert.git @20190811 |
? | 1M QIO @40MHz |
| Globe | ?? | ?? | ?? | ? | ? | ? | 1M QIO |
| Feit | E26/E27 | Smart Wifi Bulb Color | OM60/RGBW BPA800/RGBW | GPIO5=PWM1, GPIO12=PWM2, GPIO4=CLK, GPIO13=ENABLE, GPIO14=DATA(SM16716) |
Tasmota Template If the bulb is not in the blinking state, turn bulb On-Off-On-Off-On. |
1M QIO | |
| Globe | ?? | ?? | ?? | ? | ? | ? | 1M QIO |
| Lohas | E14 | Smart Bulb LED Wifi | LH-ZN123-2-2700 | MY9291: Data pin: GPIO13, Clock Pin: GPIO15 | Firmware updated on one, but not on the other. Uses an MY9291 driver | 1M QIO | |
| Luminea | E27 | Home Control | ZX-2831-675 | GPIO5: PWM1, GPIO12: PWM2 | Produced for PEARL GmbH | 1M QIO | |
| Luminea | E27 | Home Control | ZX-2832-675 LAV-100.rgbw | GPIO5: PWM4 (White) | Although this bulb is a true RGBW Bulb, no suiteable configuration for controlling RGB was found yet. | 1M QIO | |
| Luminea | E14 | RGBW Bulb 4,5Watt | NX-4462-675 | GPIO5: PWM4, GPIO12: PWM2, GPIO14: PWM3, GPIO4: PWM1 | Produced for PEARL GmbH | 1M QIO | |
| Lyasi | E27 | Wifi Smart Birne | PT-BW09 | DI=GPIO4,DCKI=GPIO5 | ? | ? | 1M QIO |
| Mirabella | B22 | Genio Wifi Dimmable 9W LED (Warm White) | I002333 | GPIO13:PWM1 | KMart, clamshell blister pack | ? | 1M QIO |
| Mirabella | E27 | Genio Wifi Dimmable Cool White | I002334 | ? | ? | https://mirabellagenio.net.au/ | ? |
| Mirabella | B22 | Genio Wifi Dimmable 9W LED (Warm Cool Day) | I002337 | GPIO5:PWM1=Cold6500K, GPIO13:PWM2=Warm2700K | KMart, clamshell blister pack | ? | 1M QIO @40MHz |
| Mirabella | B22 | Genio Wifi Dimmable 9W LED (Warm White) | I002605 | GPIO13:PWM1 | Woolworths, cardboard packaging | ? | 1M QIO |
| Mirabella | E27/B22 | Genio Wifi RGBW | ? | GPIO4: PWM1, GPIO12: PWM2, GPIO14: PWM3, GPIO5: PWM4 | ? | https://mirabellagenio.net.au/ | 1MB |
| Merkury | E27 | A21 Smart Light Bulb 75W Color | MI-BW904-999W | GPIO4=CLK, GPIO5=PWM1 (warm White), GPIO13=ENABLE (color leds), GPIO14=DATA | - | ? | |
| Merkury | E27 | BR30 Smart Light Bulb 65W Tunable White LED | ? | GPIO4 PWM1 GPIO5 PWM1 GPIO12 PWM2 | - | ? | ? |
| Merkury | E26 | A19 Smart Light Bulb 9W White Dimmable | MIC-BW902-999W | GPIO5=PWM1 | US model number maybe MI-BW902-999WS | ? | ? |
| Queo | E27 | Fcmila Bulb | ?? | GPIO 4 PWM 5 = white GPIO 12 PWM 2 = green GPIO 13 PWM 3= blue GPIO 14 PWM 1 = red GPIO 2 PWM 4 to get slider (PWM 4 or 5 can be swapped seems same result) | Tasmota Generic 18 | ? | 1M DOUT @ 40MHz |
| Syska | B22 | Smartlight Wi-fi Enabled Bulb | SSK-SMW-7W | Generic GPIO4=PWM1, GPIO5=PWM4, GPIO12=PWM2, GPIO14=PWM3 & GPIO15=PWM5(temperature) | Use Tasmota RGBWW config and SetOption17 1 & SetOption59 1
|
N | 1M QIO |
| Teckin SB50 | E27 | Smart LED Bulb | ? | GPIO4: PWM4 (40), GPI12: PWM2 (38), GPI13: PWM3 (39), GPI14: PWM1 (37) | Template | ? | 1M DOUT @ 40MHz |
| EXTSUD | E27 | 10W RGB Dimmerabile WiFi | ? | ? | AiLight 27 Profile | ? | ? |
| Arilux | E14 | WiFi Smart Bulb | YX-L01C-E4 | GPIO4=Data, GPIO5=DCKI | Uses a MY9291 LED Driver. ch0=w, ch1=b, ch2=g, ch3=r, ESP8266EX | ? | 1M QIO |
| Bomcosy/AOJA | E27 | 7W E27 RGB CW | ? | GPIO4: PWM1, GPIO5: PWM4, GPIO12: PWM2, GPIO13: PWM5, GPIO14: PWM3 | Amazon.de Amazon.co.uk Template:{"NAME":"Generic","GPIO":[0,0,0,0,37,40,0,0,38,41,39,0,0],"FLAG":1,"BASE":18} | ? | 1M QIO @ 40MHz |
| Vendor | Area | Device Name | Vendors device ID | GPIOs | Notes | 2nd MCU | Flash size/mode |
|---|---|---|---|---|---|---|---|
| Costco/CE | US | Smart Dimmer Switch | 1248524 | ? | - | ? | ? |
| Martin Jerry | US | Smart Dimmer | ? | ? | - | ? | ? |
| Costco/CE | CA | Smart Dimmer Switch | CE smart Home WF500D | GPIO13=Tuya RX, GPIO15=Tuya TX | use Tasmota Tuya Dimmer (54) | ? | ? |
| Gosund | US | 120 Wi-Fi Smart Light Switch | KS-602S | GPIO0=Button1, GPIO1=Led1i(green), GPIO12=Relay1, GPIO14=Led2i(red) | Works with Tasmota Generic Module | 1M | |
| Kuled | US | Smart Wifi Light Switch | KS-602S | GPIO0=Button1, GPIO12=Relay1, GPIO13=Led1 | Use Tasmota Generic Module NOTE: If you do not want LED on when switch is off, use Led1i for GPIO13 | ? | 1M QIO |
| Moes House | US | Smart Wall Switch 1-Gang | WF-WS01 | GPIO3 = Button1, GPIO4 = Relay1, GPIO14 = Led1 | Works with Tasmota Generic Module | ? | 1M |
| Moes House | US | Smart Wall Switch 2-Gang | WF-WS02 | GPIO2 = Led2, GPIO5 = Button2, GPIO12 = Button1, GPIO13 = Relay1, GPIO15 = Relay2, GPIO16 = Led1 | Works with Tasmota Generic Module | ? | 1M |
| Moes House | US | Smart Wall Switch 3-Gang | WF-WS03 | GPIO2 = Led3, GPIO3 = Button2, GPIO4 = Relay2, GPIO5 = Button3, GPIO12 = Button1, GPIO13 = Relay1, GPIO14 = Led2, GPIO15 = Relay3, GPIO16 = Led1 | Works with Tasmota Generic Module | ? | 1M |
| SRL | AU | Smart Light Switch - 1 Gang | SRL 1WW | GPIO12: Button1, GPIO13: Relay1, GPIO14: Led1, | Works with Tasmota Generic Module | ? | 1M |
| SRL | AU | Smart Light Switch - 2 Gang | SRL 2WW | GPIO12: Button1, GPIO13: Relay1, GPIO14: Led1, GPIO5: Button2, GPIO15: Relay2, GPIO16: Led2 | Works with Tasmota Generic Module | ? | 1M |
| SRL | AU | Smart Light Switch - 3 Gang | SRL 3WW | GPIO12: Button1, GPIO13: Relay1, GPIO14: Led1, GPIO5: Button2, GPIO15: Relay2, GPIO16: Led2, GPIO3: button3, GPIO4: relay3, GPIO??: Led3 | Works with Tasmota Generic Module | ? | 1M |
| SRL | AU | Smart Light Switch - 4 Gang | SRL 4WW | GPIO16: Button1, GPIO14: Relay1, GPIO??: Led1, GPIO3: Button2, GPIO4: Relay2, GPIO??: Led2, GPIO5: button3, GPIO5: relay3, GPIO??: Led3, GPIO12: button4, GPIO13: relay4, GPIO??: Led4 | Works with Tasmota Generic Module | ? | 1M |
| Smart Life | EU | Smart Wall Switch 3 Gang | CD302 | GPIO13=Relay1, GPIO3(RX)=Button1, GPIO14=Led1i, GPIO15=Relay2, GPIO12=Button2, GPIO16=Led2i, GPIO4=Relay3, GPIO5=Button3, GPIO1=Led3i, GPIO0=Led4 (Red) | Works with Tasmota Generic Module | ? | 1M QIO |
| TONBUX | US | Smart Light Switch | AMZ180648 | ? | Works with Tasmota Generic Module | ? | 1M QIO |
| Vendor | Area | Device Name | Vendors device ID | GPIOs | Notes | 2nd MCU | Flash size/mode |
|---|---|---|---|---|---|---|---|
| Oittm | CN | Smart Mosquito Killer | MK-01 | GPIO2=Button1, GPIO15=Led1i (Blue LED), GPIO5=Fan, GPIO12=UV LEDs, GPIO16=White LEDs | Tasmota Generic Module | no | 1M QIO |
| Auvisio | EU | Infrared Transceiver | NX-4519-675 | GPIO4=Led1,GPIO5=IRrecv,GPIO14=IRSend | Tasmota Generic Module | ? | 1M |
Battery-powered Sensors (Note Tasmota is not designed to run on battery powered devices. There is NO deep sleep)
| Vendor | Area | Device Name | Vendors device ID | GPIOs | Notes | 2nd MCU | Flash size/mode |
|---|---|---|---|---|---|---|---|
| Luminea | EU | WLAN-PIR-Bewegungsmelder | XMD-101.app | -- | STM32 as 2nd MCU; Due to the 2nd MCU, this device is currently not supported by tasmota (06 March 2019) | Y | 1M QIO @ 40MHz |
| Luminea | EU | WLAN-Door/Window Sensor | NX-4470-675 | -- | ? | ? | ? |