:::warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues.
Note also that while Cube Black is fully supported by PX4, support for Cube Yellow and Cube Orange is Experimental. :::
This quick start guide shows how to power the Cube® flight controllers and connect their most important peripherals.
:::tip The instructions apply to all Cube variants, including Cube Black, Cube Yellow and Cube Orange. Further/updated information may be available in the Cube User Manual (Cube Docs). :::
Cube comes with most (or all) of the accessories you will need when purchased.
The exception is that some kits do not include a GPS, which will have to be purchased separately (see below).
The image below shows how to connect the most important sensors and peripherals. We'll go through each of these in detail in the following sections.
- 数传系统 — 允许您计划/运行任务，实时控制和监控飞行器状态。 典型的包括数传、平板电脑/PC、地面站软件。
- 蜂鸣器 — 提供声音信号显示UAV目前的状态。
- 远程控制接收系统 — 连接手持发射器能够手动操控飞行（如图所述是一个PWM 接收器能包括 PWM->PPM 转换器）。
- （专用） 安全开关 — 按下以解锁和锁定电机。 如果您没有使用推荐的内置安全开关的 GPS 时，安全开关是必须的。
- GPS、罗盘、LED、安全开关 — 推荐的GPS模块包括GPS、罗盘、LED 和安全开关。
- 电源系统 — 电源线和电机ESC。 包括锂电池、电源模块和可选的电源报警系统（如果电池电量低于预定时发出警报）。
:::note
The port labeled GPS2 maps to TEL4 in PX4 (i.e. if connecting to the port labeled GPS2, assign the serial port configuration parameter for the connected hardware to TEL4).
:::
:::tip More information about available ports can be found here: Cube > Ports. :::
Mount the Cube as close as possible to your vehicle’s center of gravity, ideally oriented top-side up and with the arrow pointing towards the front of the vehicle (note the subtle arrow marker on top of the cube)
:::note If the controller cannot be mounted in the recommended/default orientation (e.g. due to space constraints) you will need to configure the autopilot software with the orientation that you actually used: Flight Controller Orientation. :::
The Cube can be mounted using either vibration-damping foam pads (included in the kit) or mounting screws. The mounting screws in the Cube accessories are designed for a 1.8mm thick frameboard. Customized screws are supposed to be M2.5 with thread length inside Cube in range 6mm~7.55mm.
The recommended GPS modules are the Here and Here+, both of which incorporate a GPS module, Compass, Safety Switch and LEDs.
:::note The difference between the modules is that Here+ supports centimeter level positioning via RTK. Otherwise they are used/connected in the same way. :::
The module should be mounted on the frame as far away from other electronics as possible, with the direction marker towards the front of the vehicle (separating the compass from other electronics will reduce interference). It must be connected to the GPS1 port using the supplied 8-pin cable.
The diagram below shows a schematic view of the module and its connections.
:::note The GPS module's integrated safety switch is enabled by default (when enabled, PX4 will not let you arm the vehicle). To disable the safety press and hold the safety switch for 1 second. You can press the safety switch again to enable safety and disarm the vehicle (this can be useful if, for whatever reason, you are unable to disarm the vehicle from your remote control or ground station). :::
:::tip If you want to use an old-style 6-pin GPS module, the kit comes with a cable that you can use to connect both the GPS and Safety Switch. :::
The dedicated safety switch that comes with the Cube is only required if you are not using the recommended GPS (which has an inbuilt safety switch).
If you are flying without the GPS you must attach the switch directly to the GPS1 port in order to be able to arm the vehicle and fly (or via a supplied cable if using an old-style 6-pin GPS).
The buzzer provides audio signals to that indicate UAV status. This should be connected to the USB port as shown (no further configuration is required).
A remote control (RC) radio system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes).
You will need to select a compatible transmitter/receiver and then bind them so that they communicate (read the instructions that come with your specific transmitter/receiver).
The instructions below show how to connect the different types of receivers.
Connect the ground(-),power(+),and signal(S) wires to the RC pins using the provided 3-wire servo cable.
Spektrum DSM, DSM2, and DSM-X Satellite RC receivers connect to the SPKT/DSM port.
The Cube cannot directly connect to PPM or PWM receivers that have an individual wire for each channel. PWM receivers must therefore connect to the RCIN port via a PPM encoder module, which may be purchased from hex.aero or proficnc.com.
Cube is typically powered from a Lithium Ion Polymer (LiPo) Battery via a Power Module (supplied with the kit) that is connected to the POWER1 port. The power module provides reliable supply and voltage/current indication to the board and may separately supply power to ESCs that are used to drive motors on a multicopter vehicle.
A typical power setup for a Multicopter vehicle is shown below.
A telemetry system allows you to communicate with, monitor, and control a vehicle in flight from a ground station (for example, you can direct the UAV to a particular position, or upload a new mission).
The communication channel is via Telemetry Radios. The vehicle-based radio should be connected to the TELEM1 port (if connected to this port, no further configuration is required). The other radio is connected to your ground station computer or mobile device (usually via USB).
SD cards are highly recommended as they are needed to log and analyse flight details, to run missions, and to use UAVCAN-bus hardware. Insert the Micro-SD card into Cube as shown (if not already present).
:::tip For more information see Basic Concepts > SD Cards (Removable Memory). :::
Motors/servos are connected to the MAIN and AUX ports in the order specified for your vehicle in the Airframe Reference.
:::note This reference lists the output port to motor/servo mapping for all supported air and ground frames (if your frame is not listed in the reference then use a "generic" airframe of the correct type). :::
:::caution The mapping is not consistent across frames (e.g. you can't rely on the throttle being on the same output for all plane frames). Make sure to use the correct mapping for your vehicle. :::
The wiring and configuration of optional/less common components is covered within the topics for individual peripherals.
:::note
If connecting peripherals to the port labeled GPS2, assign the PX4 serial port configuration parameter for the hardware to TEL4 (not GPS2).
:::
Configuration is performed using QGroundContro.
After downloading, installing and running QGroundControl, connect the board to your computer as shown.
Basic/common configuration information is covered in: Autopilot Configuration.
QuadPlane specific configuration is covered here: QuadPlane VTOL Configuration
- Cube Black
- Cube Yellow
- Cube Orange
- Cube Docs (Manufacturer):