Uctronics USB Ethernet adapter not detected...

[senses3]

I've got yet another uctronics issue. For some reason the adapter does not show up in lsusb at all. it works fine on any other system I tested it with but will not show up on any wyze cam (v2) with lsusb and the issue persists across any firmware I am running, however I am now running v4.98.1002. I've gone through the all the realtek mac address stuff and it all checks out fine.

#wz_mini configuration

#### W E B CAMERA###
##THIS MODE DISABLES EVERYTHING AND IT WILL
## WORK AS A WEB CAMERA FOR YOUR PC ***ONLY***
WEB_CAM_ENABLE="false"
WEB_CAM_BIT_RATE="8000"
WEB_CAM_FPS_RATE="25"

#####NETWORKING#####
CUSTOM_HOSTNAME="WCV3"

ENABLE_USB_ETH="true"
ENABLE_USB_ETH_MODULE_AUTODETECT="true"
ENABLE_USB_ETH_MODULE_MANUAL=""
USB_ETH_MAC_ADDR="00:E0:4C:36:00:01"

ENABLE_USB_DIRECT="false"
USB_DIRECT_MAC_ADDR="02:01:02:03:04:08"

ENABLE_USB_RNDIS="false"

ENABLE_IPV6="false"

ENABLE_WIREGUARD="false"
WIREGUARD_IPV4=""
WIREGUARD_PEER_ENDPOINT=""
WIREGUARD_PEER_PUBLIC_KEY=""
WIREGUARD_PEER_ALLOWED_IPS=""
WIREGUARD_PEER_KEEP_ALIVE=""

ENABLE_IPTABLES="false"

ENABLE_NFSv4="false"

ENABLE_RTL8189FS_DRIVER="true"
ENABLE_ATBM603X_DRIVER="true"

NTP_SERVER=""

##### NETWORK INTERFACE BONDING #####
BONDING_ENABLED="true"
BONDING_PRIMARY_INTERFACE="eth0"
BONDING_SECONDARY_INTERFACE="wlan0"
BONDING_LINK_MONITORING_FREQ_MS="100"
BONDING_DOWN_DELAY_MS="5000"
BONDING_UP_DELAY_MS="5000"
BONDING_FAIL_OVER_MAC="0"

#####ACCESSORIES#####
REMOTE_SPOTLIGHT="false"

#####VIDEO STREAM#####
RTSP_LOGIN="admin"
RTSP_PASSWORD=""
RTSP_PORT="8554"

RTSP_HI_RES_ENABLED="false"
RTSP_HI_RES_ENABLE_AUDIO="false"

RTSP_LOW_RES_ENABLED="false"
RTSP_LOW_RES_ENABLE_AUDIO="false"

RTSP_AUTH_DISABLE="false"

VIDEO_0_MAX_BITRATE=""
VIDEO_0_TARGET_BITRATE=""
VIDEO_0_ENC_PARAMETER=""
VIDEO_0_FPS=""

VIDEO_1_MAX_BITRATE=""
VIDEO_1_TARGET_BITRATE=""
VIDEO_1_ENC_PARAMETER=""
VIDEO_1_FPS=""

GO2RTC_SERVER_ENABLED="false"
GO2RTC_HI_RES_ENABLED="false"
GO2RTC_HI_RES_ENABLE_AUDIO="false"
GO2RTC_LOW_RES_ENABLED="false"
GO2RTC_LOW_RES_ENABLE_AUDIO="false"

#####RTMP STREAMING#####
#### REQUIRES RTSP ####
### AND RTSP AUDIO ###
RTMP_STREAM_ENABLED="false"
RTMP_STREAM_FEED="video1_unicast"
RTMP_STREAM_SERVICE="youtube"
RTMP_STREAM_DISABLE_AUDIO="false"
RTMP_STREAM_YOUTUBE_KEY=""
RTMP_STREAM_TWITCH_KEY=""
RTMP_STREAM_FACEBOOK_KEY=""

#####GENERAL#####
LIBCALLBACK_ENABLE="true"
ENABLE_SWAP="true"
ENABLE_USB_STORAGE="false"
ENABLE_EXT4="false"
ENABLE_CIFS="false"
DISABLE_FW_UPGRADE="true"
AUDIO_PROMPT_VOLUME="50"
ENABLE_MP4_WRITE="false"
NIGHT_DROP_DISABLE="false"
DISABLE_MOTOR="false"
ENABLE_FSCK_ON_BOOT="false"
ENABLE_CAR_DRIVER="false"
ENABLE_LOCAL_DNS="false"
ENABLE_CRONTAB="false"
ENABLE_SELFHOSTED_MODE="true"

#####DEBUG#####
#drops you to a shell via serial, doesn't load app_init.sh
DEBUG_ENABLED="false"
DEBUG_INITRAMFS_ENABLED="false"
DEBUG_PASSWORD="false"
ENABLE_SYSLOG_SAVE="false"

####WEB####
WEB_SERVER_ENABLED="true"
WEB_SERVER_AUTH="true"
WEB_SERVER_LOGIN="admin"
WEB_SERVER_PASSWORD=""
WEB_SERVER_OPTIONS="cam config car jpeg status"

#####SCRIPTING#####
CUSTOM_SCRIPT_PATH=""

Is there a config option I am missing to enable USB devices or should I try to get a new adapter?

[gtxaspec]

Can you try a different USB device and run lsusb to verify USB operation?

[senses3]

yeah i just stuck a flash drive in the usb-a port and it sees it. I don't have another micro-usb device with power out to test microusb.

[gtxaspec]

The v2's micro USB is power only. You will need a full size USB A adapter on the v2

[senses3]

awww wow ok I didnt see that anywhere in the docs.

thanks