HydraFW Binary I2C mode guide

HydraFW binary I2C mode guide

This guide is updated towards firmware release HydraFW v0.9 Beta

Commands

Once the I2C mode has been selected, the following commands are available :

• 0b00000000 Return to main mode. Returns BBIO1
• 0b00000001 Mode identification. Returns I2C1
• 0b00000010 I2C start bit
• 0b00000011 I2C stop bit
• 0b00000100 I2C read byte
• 0b00000110 I2C ACK bit
• 0b00000111 I2C NACK bit
• 0b00001000 I2C Write-then-read
• 0b00001111 Sniff all I2C traffic
• 0b0001xxxx Bulk I2C write
• 0b01000x00 Configure I2C peripheral
• 0b011000xx Set I2C speed
• 0b11xxxxxx Binary Auxiliary pins

Command details

I2C start bit (0b00000010)

Send an I2C start bit. Returns 0x01

I2C stop bit (0b00000011)

Send an I2C stop bit. Returns 0x01

I2C read byte (0b00000100)

Reads a byte from the I2C bus, returns the byte. You must ACK or NACK each byte manually!

I2C ACK bit (0b00000110)

Send an I2C ACK bit after reading a byte. Tells a slave device that you will read another byte. Returns 0x01

I2C NACK bit (0b00000111)

Send an I2C NACK bit after reading a byte. Tells a slave device that you will stop reading, next bit should be an I2C stop bit. Returns 0x01

I2C Write-then-read (0b00001000)

This command is used to send at most 4096 bytes and will read at most 4096 bytes of data. Format :

Byte 1           2          3          4          5         6        ...
|----------|----------|----------|----------|----------|----------|------...
 [command ] [   Bytes to write  ] [   Bytes to read   ] [ Data to write

The bytes to read/write are in big-endian format.

• All data will be buffered before being sent to the I2C bus. Read data will also be buffered on the Hydrabus before being sent back to the user.
• I2C start bit is sent before sending the data.
• All read bytes are ACKed, except the last byte which is NACKed.
• At the end of the read process, Hydrabus sends an I2C stop.

More information can be found here : http://dangerousprototypes.com/docs/I2C_(binary)#0x08_-_Write_then_read

Sniff all I2C traffic (0b00001111)

To be done

Bulk I2C write (0b0001xxxx)

In this mode, the last 4 bits of the command define the number of bytes to write (from 1 to 16) (Command 0b00010000 will send 1 byte). Hydrabus replies 0x01 to the bulk I2C command. After each data byte the Hydrabus returns the ACK 0x00 or NACK 0x01 bit from the slave device.

Set I2C speed (0b011000xx)

This command sets the I2C device speed. The two last bits will select the speed (in kHz) within the following list :

• 0b00 => 50 kHz
• 0b01 => 100 kHz
• 0b10 => 400 kHz
• 0b11 => 1000 kHz

This commands returns 0x01 if successful, 0x00 in case of error.

Configure I2C peripheral (0b01000x00)

This allows to set the following parameters :

• x sets the pull-up resistors (if 1 use internal on-board pull-up resistors about 50Kohm else use external on-board pull-up resistors)

See https://github.com/hydrabus/hydrafw/wiki/HydraFW-I2C-guide for explanation.

This commands returns 0x01 if successful, 0x00 in case of error.

Example script

The following python script can be used to read 4096 bytes from a 24AA I2C EEPROM :

import hexdump
import serial
import struct

# Open serial port
ser = serial.Serial('/dev/ttyACM0', 115200)

# Open binary mode
for i in xrange(20):
    ser.write("\x00")
if "BBIO1" not in ser.read(5):
    print "Could not get into binary mode"
    quit()

# Switching to I2C mode
ser.write('\x02')
if "I2C1" not in ser.read(4):
    print "Cannot set I2C mode"
    quit()

# Reading information
while (addr < 4096*size):
    #Write-then-read. 4 bytes to write, 4096 bytes to read 
    ser.write('\x08\x00\x04\x10\x00')
    #Read command(\x03) and starting address (\x00\x00\x00)
    ser.write('\x03\x00\x00\x00')
    #Hydrabus will send \x01 in case of success...
    ser.read(1)
    #...followed by 4096 read bytes
    buff += ser.read(4096)

print hexdump.hexdump(buff)

# Return to main binary mode
ser.write('\x00')
#reset to console mode
ser.write('\x0F\n')