Argument_None.ino

/****************************************************************************************************************************
  Argument_None.ino
  For ESP32, ESP32_S2, ESP32_S3, ESP32_C3 boards with ESP32 core v2.0.0+
  Written by Khoi Hoang

  Built by Khoi Hoang https://github.com/khoih-prog/ESP32_New_TimerInterrupt
  Licensed under MIT license

  The ESP32, ESP32_S2, ESP32_C3 have two timer groups, TIMER_GROUP_0 and TIMER_GROUP_1
  1) each group of ESP32, ESP32_S2 has two general purpose hardware timers, TIMER_0 and TIMER_1
  2) each group of ESP32_C3 has ony one general purpose hardware timer, TIMER_0

  All the timers are based on 64 bits counters and 16 bit prescalers. The timer counters can be configured to count up or down
  and support automatic reload and software reload. They can also generate alarms when they reach a specific value, defined by
  the software. The value of the counter can be read by the software program.

  Now even you use all these new 16 ISR-based timers,with their maximum interval practically unlimited (limited only by
  unsigned long miliseconds), you just consume only one ESP32-S2 timer and avoid conflicting with other cores' tasks.
  The accuracy is nearly perfect compared to software timers. The most important feature is they're ISR-based timers
  Therefore, their executions are not blocked by bad-behaving functions / tasks.
  This important feature is absolutely necessary for mission-critical tasks.
*****************************************************************************************************************************/

/*
   Notes:
   Special design is necessary to share data between interrupt code and the rest of your program.
   Variables usually need to be "volatile" types. Volatile tells the compiler to avoid optimizations that assume
   variable can not spontaneously change. Because your function may change variables while your program is using them,
   the compiler needs this hint. But volatile alone is often not enough.
   When accessing shared variables, usually interrupts must be disabled. Even with volatile,
   if the interrupt changes a multi-byte variable between a sequence of instructions, it can be read incorrectly.
   If your data is multiple variables, such as an array and a count, usually interrupts need to be disabled
   or the entire sequence of your code which accesses the data.
*/

#if !defined( ESP32 )
	#error This code is intended to run on the ESP32 platform! Please check your Tools->Board setting.
#endif

// These define's must be placed at the beginning before #include "_TIMERINTERRUPT_LOGLEVEL_.h"
// _TIMERINTERRUPT_LOGLEVEL_ from 0 to 4
#define _TIMERINTERRUPT_LOGLEVEL_     4

#include "TimerInterrupt_Generic.h"

// Don't use PIN_D1 in core v2.0.0 and v2.0.1. Check https://github.com/espressif/arduino-esp32/issues/5868
// Don't use PIN_D2 with ESP32_C3 (crash)
#define PIN_D19             19        // Pin D19 mapped to pin GPIO9 of ESP32
#define PIN_D3               3        // Pin D3 mapped to pin GPIO3/RX0 of ESP32

// With core v2.0.0+, you can't use Serial.print/println in ISR or crash.
// and you can't use float calculation inside ISR
// Only OK in core v1.0.6-
bool IRAM_ATTR TimerHandler0(void * timerNo)
{
	static bool toggle0 = false;

	//timer interrupt toggles pin PIN_D19
	digitalWrite(PIN_D19, toggle0);
	toggle0 = !toggle0;

	return true;
}

// With core v2.0.0+, you can't use Serial.print/println in ISR or crash.
// and you can't use float calculation inside ISR
// Only OK in core v1.0.6-
bool IRAM_ATTR TimerHandler1(void * timerNo)
{
	/////////////////////////////////////////////////////////

	static bool toggle1 = false;

	//timer interrupt toggles outputPin
	digitalWrite(PIN_D3, toggle1);
	toggle1 = !toggle1;

	return true;
}

#define TIMER0_INTERVAL_MS        100

#define TIMER1_INTERVAL_MS        5000

// Init ESP32 timer 0 and 1
ESP32Timer ITimer0(0);
ESP32Timer ITimer1(1);

void setup()
{
	pinMode(PIN_D19, OUTPUT);
	pinMode(PIN_D3,  OUTPUT);

	Serial.begin(115200);

  while (!Serial && millis() < 5000);

  delay(500);

	Serial.print(F("\nStarting Argument_None on "));
	Serial.println(ARDUINO_BOARD);
	Serial.println(ESP32_TIMER_INTERRUPT_VERSION);
	Serial.println(TIMER_INTERRUPT_GENERIC_VERSION);
	Serial.print(F("CPU Frequency = "));
	Serial.print(F_CPU / 1000000);
	Serial.println(F(" MHz"));

	// Using ESP32  => 80 / 160 / 240MHz CPU clock ,
	// For 64-bit timer counter
	// For 16-bit timer prescaler up to 1024

	// Interval in microsecs
	if (ITimer0.attachInterruptInterval(TIMER0_INTERVAL_MS * 1000, TimerHandler0))
		//if (ITimer0.attachInterrupt(1, TimerHandler0))
	{
		Serial.print(F("Starting  ITimer0 OK, millis() = "));
		Serial.println(millis());
	}
	else
		Serial.println(F("Can't set ITimer0. Select another Timer, freq. or timer"));


	// Interval in microsecs
	if (ITimer1.attachInterruptInterval(TIMER1_INTERVAL_MS * 1000, TimerHandler1))
		//if (ITimer1.attachInterrupt(2, TimerHandler1))
	{
		Serial.print(F("Starting  ITimer1 OK, millis() = "));
		Serial.println(millis());
	}
	else
		Serial.println(F("Can't set ITimer1. Select another Timer, freq. or timer"));
}

void loop()
{
	delay(1);
}