-
Notifications
You must be signed in to change notification settings - Fork 0
/
vkBasalt.conf
107 lines (90 loc) · 3.54 KB
/
vkBasalt.conf
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
#effects is a colon seperated list of effect to use
#e.g.: effects = fxaa:cas
#effects will be run in order from left to right
#one effect can be run multiple times e.g. smaa:smaa:cas
#cas - Contrast Adaptive Sharpening
#dls - Denoised Luma Sharpening
#fxaa - Fast Approximate Anti-Aliasing
#smaa - Enhanced Subpixel Morphological Antialiasing
#lut - Color LookUp Table
effects = cas:tonemap
reshadeTexturePath = "/home/sue/.config/vkBasalt/reshade/Textures/"
reshadeIncludePath = "/home/sue/.config/vkBasalt/reshade/Shaders/"
tonemap = "/home/sue/.config/vkBasalt/reshade/Shaders/Tonemap.fx"
#toggleKey toggles the effects on/off
toggleKey = Home
#enableOnLaunch sets if the effects are enabled when started
enableOnLaunch = True
#casSharpness specifies the amount of sharpning in the CAS shader.
#0.0 less sharp, less artefacts, but not off
#1.0 maximum sharp more artefacts
#Everything in between is possible
#negative values sharpen even less, up to -1.0 make a visible difference
casSharpness = 1
#dlsSharpness specifies the amount of sharpening in the Denoised Luma Sharpening shader.
#Increase to sharpen details within the image.
#0.0 less sharp, less artefacts, but not off
#1.0 maximum sharp more artefacts
dlsSharpness = 0.5
#dlsDenoise specifies the amount of denoising in the Denoised Luma Sharpening shader.
#Increase to limit how intensely film grain within the image gets sharpened.
#0.0 min
#1.0 max
dlsDenoise = 0.17
#fxaaQualitySubpix can effect sharpness.
#1.00 - upper limit (softer)
#0.75 - default amount of filtering
#0.50 - lower limit (sharper, less sub-pixel aliasing removal)
#0.25 - almost off
#0.00 - completely off
fxaaQualitySubpix = 0.75
#fxaaQualityEdgeThreshold is the minimum amount of local contrast required to apply algorithm.
#0.333 - too little (faster)
#0.250 - low quality
#0.166 - default
#0.125 - high quality
#0.063 - overkill (slower)
fxaaQualityEdgeThreshold = 0.125
#fxaaQualityEdgeThresholdMin trims the algorithm from processing darks.
#0.0833 - upper limit (default, the start of visible unfiltered edges)
#0.0625 - high quality (faster)
#0.0312 - visible limit (slower)
#Special notes: due to the current implementation you
#Likely want to set this to zero.
#As colors that are mostly not-green
#will appear very dark in the green channel!
#Tune by looking at mostly non-green content,
#then start at zero and increase until aliasing is a problem.
fxaaQualityEdgeThresholdMin = 0.0312
#smaaEdgeDetection changes the edge detection shader
#luma - default
#color - might catch more edges, but is more expensive
smaaEdgeDetection = luma
#smaaThreshold specifies the threshold or sensitivity to edges
#Lowering this value you will be able to detect more edges at the expense of performance.
#Range: [0, 0.5]
#0.1 is a reasonable value, and allows to catch most visible edges.
#0.05 is a rather overkill value, that allows to catch 'em all.
smaaThreshold = 0.05
#smaaMaxSearchSteps specifies the maximum steps performed in the horizontal/vertical pattern searches
#Range: [0, 112]
#4 - low
#8 - medium
#16 - high
#32 - ultra
smaaMaxSearchSteps = 32
#smaaMaxSearchStepsDiag specifies the maximum steps performed in the diagonal pattern searches
#Range: [0, 20]
#0 - low, medium
#8 - high
#16 - ultra
smaaMaxSearchStepsDiag = 16
#smaaCornerRounding specifies how much sharp corners will be rounded
#Range: [0, 100]
#25 is a reasonable value
smaaCornerRounding = 25
#lutFile is the path to the LUT file that will be used
#supported are .CUBE files and .png with width == height * height
lutFile = "/path/to/lut"
Gamma = 0.790
Exposure = 0.059