oricutron.cfg

;
; Example config file for Oricutron
;

;                 ----------------------------------

; ROM files. (NOTE: For roms, DO NOT include the ".rom" file
; extension. These are added automatically.
; If a file with the same name, but with a ".sym" extension
; is found, symbols will be loaded from it and used in the
; debugger when the ROM in question is active.

; Filename of Oric Atmos ROM
;atmosrom = 'roms/basic11b'

; Filename of the Oric-1 ROM
;oric1rom = 'roms/basic10'

; Filename of the Pravetz 8D ROM
;pravetzrom = 'roms/pravetzt'

; Filename of ROMs for the telestrat banks
;telebank0 = ''
;telebank1 = ''
;telebank2 = ''
;telebank3 = ''
;telebank4 = ''
;telebank5 = 'roms/teleass'
;telebank6 = 'roms/hyperbas'
;telebank7 = 'roms/telmon24'

;                 ----------------------------------

; Filename of the Microdisc ROM
;mdiscrom = 'roms/microdis'

; Filename of the Byte Drive 500 ROM
;bd500rom = 'roms/bd500'

; Filename of the Jasmin ROM
;jasminrom = 'roms/jasmin'

; Filename of the Pravetz 8D disk ROM
;pravetz8drom = 'roms/8dos'
;pravetz8drom = 'roms/8dos2'

;                 ----------------------------------

; Type of machine to emulate (atmos, oric1, oric1-16k, telestrat, pravetz)
machine = atmos

;                 ----------------------------------

; Type of disk controller (none, microdisc, jasmin, bd500, pravetz)
disktype = none

; Write back all changes to disk images (if turned off, you have to press
; F7 to write changes back to the disk image)
diskautosave = yes

;                 ----------------------------------

; Start with this disk in drive 0 (backslash is an escape char to insert
; quotes, so double backslash is required to insert a backslash. You can use
; forward slash as a path seperator, even on windows.
;diskimage = 'assets/disks/aigledor.dsk'

;                 ----------------------------------

; Default path for tapes
;tapepath = 'tapes'

; Default path for atmos/oric-1 disks
;diskpath = 'disks'

; Default path for telestrat disks
;telediskpath = 'teledisks'

; Default path for pravetz disks
;pravdiskpath = 'pravdisks'
pravdiskautoboot = yes

;                 ----------------------------------

; Start with this tape inserted
;tapeimage = 'assets/tapes/Cyclotron.tap'

;                 ----------------------------------

; Start Oricutron in the debugger? (yes/no)
debug = no

; Load these symbols into the debugger
;symbols = 'd:/osdk/my project/build/symbols'

;                 ----------------------------------

; Specifies how ROMDIS disables ROM chip(s)
; related to BD500/BDDOS
; rom16 = yes - 64k mode (Default)
; rom16 = no  - 56k mode
;rom16 = yes

; Support BD500/DOS70
; dos70 = no (default)
;dos70 = no

;                 ----------------------------------

; Initial status bar mode (none, nofps, full)
;statusbarmode = nofps

; Render mode (soft, opengl)
rendermode = opengl

; Show scanlines? (yes/no)
scanlines = no

; Maintain correct aspect ratio in 50Hz/60Hz modes
aratio = yes

; Horizontal stretch? (yes/no)  <-- opengl only
hstretch = no

; PAL ghosting? (yes/no)  <-- opengl only
palghosting = no

; Start fullscreen?
fullscreen = no

; Tell SDL to use a hardware surface? (might increase speed in fullscreen, or
; it might do nothing, or it might make it worse). (software rendering only)
hwsurface = yes

; Force video display bit depth, either 16 or 32 (on some hardware, 16 can
; extremely slow, ie. eeepc clones). Normally Oricutron will guess the best
; one, but if it seems to be slow, try setting this to 16 or 32 to see if
; it makes a difference. (software rendering only)
;swdepth = 16

;                 ----------------------------------

; RAM pattern on powerup (0 or 1)
rampattern = 0

;                 ----------------------------------

; Lightpen (yes/no)
lightpen = no

; Enable printing to 'printer_out.txt'
; default enabled
;printenable = yes

; Filter printed symbols in 'printer_out.txt'
; select 'no' for raw binay mode
;printfilter = yes

; Enable audio DC adjustment
; default enabled
;dcadjust = yes

; Enable sound loopback
; default disabled
;soundloopon = no

; ACIA emulation back-end name:
;   'none' - no serial present
;   'loopback' - for testing - all TX data is returned to RX
;   'modem[:port][:ipv6]' - emulates com port with attached modem,
;                    only minimal AT command set is supported and
;                    data is redirected to TCP. Default port is 23 (telnet).
;                    if :ipv6 is added at the end uses IPv6 instead of IPv4
;   'com:115200,8,N,1,<device>' - use real or virtual <device> on host as emulated ACIA
;                   baudrate, data bits, parity and stop bits can be set as needed
;     ex.:  Windows: 'com:115200,8,N,1,COM1'
;           Linux:   'com:115200,8,N,1,/dev/ttyUSB0'
serial = 'none'

; Set serial base address. Default: $31c
serial_address = $31c

; Joystick interface for Atmos/Oric-1 mode. Telestrat has its own built-in standard.
; Options are 'none', 'altai', 'pase' or 'ijk'
joyinterface = none

; How to emulate joysticks attached to the above interface
; Options are 'none', 'kbjoy1', 'kbjoy2', 'sdljoyN' (where n is 0 to 9)
joystick_a = kbjoy1
joystick_b = none

; How to emulate joysticks attached to the telestrat
; Options are 'none', 'kbjoy1', 'kbjoy2', 'sdljoyN', 'mouse'
telejoy_a = kbjoy1
telejoy_b = none

; Keys to emulate joystick, set 1
; NOTE: "fire2" is only available on telestrat
; NOTE: "fire3" is only available on telestrat (right port)
kbjoy1_up = 'KP8'
kbjoy1_down = 'KP2'
kbjoy1_left = 'KP4'
kbjoy1_right = 'KP6'
kbjoy1_fire1 = 'KP_ENTER'
kbjoy1_fire2 = 'KP_PLUS'
kbjoy1_fire3 = 'KP_MINUS'

; Keys to emulate joystick, set 2
kbjoy2_up = 'W'
kbjoy2_down = 'S'
kbjoy2_left = 'A'
kbjoy2_right = 'D'
kbjoy2_fire1 = 'SPACE'
kbjoy2_fire2 = 'N'
kbjoy2_fire3 = 'LALT'

; Visual keyboard
show_keyboard = yes
sticky_mod_keys = yes
;autoload_keyboard_mapping = 'keymap/my_keymap.kma'

; Disable menu color scheme
;disable_menuscheme = no

; ch376 chip emulation. This chip can read a usbkey. For more information : http://orix.oric.org
; only available in telestrat mode
ch376 = no
twilighte_board = no