KlipperScreen.conf

[main]
job_complete_timeout: 120
default_printer: Zippy Print

[printer Zippy Print]
power_devices: Printer
titlebar_items: chamber, spool, steppers
titlebar_name_type: full
camera_url: http://mainsailos/webcam/?action=stream

[menu __main zippy]
name: Zippy
icon: heat-up

[menu __main zippy heat_soak]
name: Heat Soak
icon: heat-up
method: printer.gcode.script
params: {"script":"HEAT_SOAK"}
enable: {{ printer.power_devices.count > 0 }}

[menu __main zippy filament_change]
name: Change Filament
icon: heat-up
method: printer.gcode.script
params: {"script":"CHANGE_FILAMENT"}
enable: {{ printer.power_devices.count > 0 }}

[menu __main zippy nozzle_clean]
name: Clean Nozzle
icon: heat-up
method: printer.gcode.script
params: {"script":"CLEAN_NOZZLE"}
enable: {{ printer.power_devices.count > 0 }}

[menu __main zippy maintenance]
name: Maintenance
icon: heat-up
method: printer.gcode.script
params: {"script":"MAINTENANCE"}
enable: {{ printer.power_devices.count > 0 }}

#~# --- Do not edit below this line. This section is auto generated --- #~#
#~#
#~# [main]
#~# screen_blanking = 7200
#~# font_size = small
#~# confirm_estop = True
#~# show_heater_power = True
#~# invert_y = True
#~# move_speed_xy = 150
#~# print_sort_dir = date_desc
#~# 
#~# [displayed_macros Zippy Print]
#~# begin_layer = False
#~# cancel_print = False
#~# filament_runout = False
#~# g29 = False
#~# g27 = False
#~# hyperlapse = False
#~# initialize_variable = False
#~# load_print = False
#~# notify = False
#~# m205 = False
#~# m900 = False
#~# present_print = False
#~# power_off_printer = False
#~# m204 = False
#~# m420 = False
#~# post_end = False
#~# m701 = False
#~# m600 = False
#~# m73 = False
#~# m702 = False
#~# prime_nozz = False
#~# set_adv_velocity = False
#~# telegram_filament_runout = False
#~# set_wled = False
#~# test_stream_delay = False
#~# retract = False
#~# wipe_line = False
#~# publish_alert = False
#~# save_at_end = False
#~# query_environment = False
#~# present_print_old = False
#~# pre_start = False
#~# timelapse_take_frame = False
#~# timelapse_render = False
#~# save_if_set = False
#~# wled_on = False
#~# wled_off = False
#~# alert_beep_on = False
#~# beep = False
#~# boot_up = False
#~# be_mine_tune = False
#~# cena_tune = False
#~# change_tune = False
#~# end_tones = False
#~# end_tune = False
#~# complete_print = False
#~# dehumid_off = False
#~# game_over_tune = False
#~# dehumid_on = False
#~# end_print = False
#~# extract = False
#~# get_timelapse_setup = False
#~# level_bed_now = False
#~# lazy_home = False
#~# m125 = False
#~# m600cfg = False
#~# hello_world = False
#~# move_percent = False
#~# jobcenter = False
#~# mario_tune = False
#~# load_filament = False
#~# pause = False
#~# home_if_needed = False
#~# imperial_tune = False
#~# mesh_tune = False
#~# nevermore_off = False
#~# pressure_advance_list = False
#~# pa_cal = False
#~# nevermore_on = False
#~# pause_park = False
#~# pressure_advance_remove = False
#~# low_temp_check = False
#~# m300 = False
#~# query_ambient = False
#~# m808 = False
#~# m876 = False
#~# power_off_display = False
#~# unsafe_raise_tool = False
#~# status_ready = False
#~# power_off_lights = False
#~# poweroff = False
#~# reboot = False
#~# query_spool = False
#~# pressure_advance_add = False
#~# resume = False
#~# query_chamber = False
#~# power_on_lights = False
#~# prep_print = False
#~# power_on_filter = False
#~# status_busy = False
#~# starter_tune = False
#~# unload_filament = False
#~# shutdown = False
#~# pressure_advance_select = False
#~# wled_control = False
#~# power_off_filter = False
#~# start_tones = False
#~# zelda_end_tune = False
#~# start_print = False
#~# zelda_ending_tune = False
#~# print_start_tune = False
#~# sweet_child_tune = False
#~# filter_on = False
#~# filter_off = False
#~# bed_fan_off = False
#~# bed_fan_on = False
#~# bed_mesh_calibrate = False
#~# compare_values = False
#~# clear_status = False
#~# exhaust_off = False
#~# exhaust_on = False
#~# go_home = False
#~# load_fil = False
#~# m141 = False
#~# g34 = False
#~# set_nozzle_leds_off = False
#~# status_leveling = False
#~# purge_macro = False
#~# set_material = False
#~# scrubber = False
#~# status_meshing = False
#~# set_logo_leds_off = False
#~# status_off = False
#~# status_homing = False
#~# wled_default = False
#~# test_chamber_temp = False
#~# set_nozzle_leds_on = False
#~# status_heating = False
#~# status_cleaning = False
#~# unload_fil = False
#~# status_printing = False
#~# status_success = False
#~# status_calibrating_z = False
#~# status_vibrating = False
#~# status_soaking = False
#~# test_resonances = False
#~# 
#~# [graph Zippy Print]
#~# temperature_fan host = False
#~#