diff --git a/content/docs/wiki/cc3200/debug-port.md b/content/docs/wiki/cc3200/debug-port.md index 25ef703..a05541e 100644 --- a/content/docs/wiki/cc3200/debug-port.md +++ b/content/docs/wiki/cc3200/debug-port.md @@ -5,7 +5,7 @@ description: "" # Debug Port ## Position of debug port on Toniebox-PCB -![/img/toniebox_pcb_debug_port.png](/img/toniebox_pcb_debug_port.png) +![Image of the debug port on the CC3200 board, showing the position of the port.](/img/toniebox_pcb_debug_port.png) The debug port runs on `3.3 V` @@ -15,7 +15,7 @@ The debug port runs on `3.3 V` 1 2 3 4 5 ``` -![/img/debug_port_pin_out.png](/img/debug_port_pin_out.png) +![Debug port with a number at each connection point.](/img/debug_port_pin_out.png) | Pin | Function | Comment | @@ -52,10 +52,11 @@ SOP2 (pin 9) high will activate the UART load mode to flash the system during de # Extract Firmware ## Introduction -Grab your favourite USB-UART **3.3V** interface, recommending those with DTR or RTS port to automate board reset. You may also use a CC3200 Launchpad, but then you will need to reset it by hand. SOP2 need to be pulled high while reset to set the cc3200 into UART-Mode. -You may have a UART to USB adapter that supports both 3.3V and 5V. In this case you should find a jumper on the board to select the correct mode. You can see examples of such jumpers here (but there are others.) **In any case, make absolutely sure that 3.3V (often labelled 3v3) is set!** +Grab your favourite USB-UART **3.3V** interface, recommending those with DTR or RTS port to automate board reset. You may also use a CC3200 Launchpad, but then you will need to reset it by hand. SOP2 need to be pulled high while reset to set the cc3200 into UART-Mode. +You may have a UART to USB adapter that supports both 3.3V and 5V. In this case you should find a jumper on the board to select the correct mode. You can see examples of such jumpers here (but there are others.) +**In any case, make absolutely sure that 3.3V (often labelled 3v3) is set or you will frie your board!** -![/img/uart_3v3-5V_jumper_black.jpg](/img/uart_3v3-5V_jumper_black.jpg) ![/img/uart_3v3-5V_jumper_switch.jpg](/img/uart_3v3-5V_jumper_switch.jpg) ![/img/uart_3v3-5V_jumper_yellow.jpg](/img/uart_3v3-5V_jumper_yellow.jpg) +![Jumper to select between 3.3 and 5 volts on a red PCB with a black pin base.](/img/uart_3v3-5V_jumper_black.jpg) ![Switch to select between 3.3 and 5 volts on a red PCB.](/img/uart_3v3-5V_jumper_switch.jpg) ![Jumper to select between 3.3 and 5 volts on a blue PCB with a yellow pin base.](/img/uart_3v3-5V_jumper_yellow.jpg) ## Toolset Use [cc3200tool](https://github.com/toniebox-reverse-engineering/cc3200tool) to extract the firmware. Just download it to your favorite location. diff --git a/static/img/uart_3v3-5V_jumper_black.jpg b/static/img/uart_3v3-5V_jumper_black.jpg index 12f988b..e9b2eae 100644 Binary files a/static/img/uart_3v3-5V_jumper_black.jpg and b/static/img/uart_3v3-5V_jumper_black.jpg differ diff --git a/static/img/uart_3v3-5V_jumper_yellow.jpg b/static/img/uart_3v3-5V_jumper_yellow.jpg index 6f02805..e1c90db 100644 Binary files a/static/img/uart_3v3-5V_jumper_yellow.jpg and b/static/img/uart_3v3-5V_jumper_yellow.jpg differ