A connector to use a LEGO Mindstorms EV3 running the ev3dev firmware (http://www.ev3dev.org) from the Open Roberta lab (http://lab.open-roberta.org). This is now included by default with ev3dev images (Thanks @dlech).
Step-by-step instruction to help you get ev3dev up and running can be found here (https://www.ev3dev.org/docs/getting-started/).
Important note for Step 1 of the manual: You have to download the ev3dev operating system for your EV3 robot via the following link: ev3dev - Github releases. Select there the file ev3dev-jessie-ev3-generic-2017-09-14.zip.
As soon as everything is installed, the connector is not enabled by default (to save memory), so you do have to enable it once:
- Connect to the LEGO brick using SSH: (Read this for the default password)
- On the brick run:
sudo systemctl unmask openrobertalab
sudo systemctl start openrobertalabAfter running the commands above, it will start automatically after a reboot. You can turn it back off by running:
sudo systemctl stop openrobertalab.service
sudo systemctl mask openrobertalab.serviceIf the openrobertalab package is installed and the service is running, the
Open Roberta Lab menu item in brickman will allow you to connect to an Open
Roberta server. This is how the menu will look like:
.
Once you selected the Open Roberta Lab menu item you'll get to this screen:
.
This offers to connect to the public server as the first item, or to a custom server as a 2nd item. The 2nd choice is mostly for developers or for using a local server. When clicking connect, the screen will show a pairing code:
.
This code will have to be entered on the web-ui to establish the link. Once that has been done a beep-sequence on the EV3 confirms the link and this screen is shown:
.
When a program contains an infinite loop, it can be killed by pressing
the enter and down buttons on the ev3 simultaneously. If this is not
enough to terminate the program, holding the back button for one second
will kill it, but together with it the connector. The connector will restart
automatically, but one needs to reconnect to the Open Roberta server again.
The package consist of two parts:
- roberta/lab.py: the connector to the open roberta lab
- this is started as a systemd service at startup
- it provides a dbus interface
- the brickman ui uses dbus for the
Open Robertamenu
- roberta/ev3.py: a hardware abstraction library
- provides the implementation for the NEPO blocks in the program
The connector talks with two main components, the server and the local brickman UI:
.
python3-ev3dev python3-bluez python3-dbus python3-gi
VERSION="1.3.2" python setup.py sdist
Resulting file is under ./dist/openrobertalab-${VERSION}.tar.gz
Now you can also build a debian package using debuild or
debuild -us -us. The new package will be in the parent folder.
To build a release for the openroberta server run
rm roberta/*~
zip -r roberta.zip roberta -x roberta/test*.py -x *__pycache__*
The easiest is to upload the debian package and install it.
scp ../openrobertalab_1.3.2-1_all.deb [email protected]:
ssh -t [email protected] "sudo dpkg --install openrobertalab_1.3.2-1_all.deb;"
Alternatively after changing single files you can do:
scp roberta/ev3.py [email protected]:
ssh -t [email protected] "sudo mv ev3.py /usr/lib/python3/dist-packages/roberta/; sudo systemctl restart openrobertalab"
Finally you can also upload through a local open roberta server (assuming your git checkout of the openroberta-lab is at the same parent dir):
mkdir -p ../openroberta-lab/RobotEV3/updateResources/ cp roberta.zip ../openroberta-lab/RobotEV3/updateResources/ev3dev/
The brickman ui will store configuration data under /etc/openroberta.conf. All configuration can be edited from the UI. If there is a need to manually change the configuration, it is advised to stop brickman.
python3 -m unittest discover roberta or nosetests.
The test require python3-httpretty, but run without python3-ev3dev.
The service writes status to the system journal.
sudo journalctl -f -b0 -u openrobertalab