Added support for "assorted small plugins".

main/CMakeLists.txt

@@ -207,12 +207,13 @@ set(LASER_SOURCE
 set(MISC_PLUGINS_SOURCE
  plugins/bltouch.c
  plugins/eventout.c
+ plugins/feed_override_m220.c
+ plugins/homing_pulloff.c
  plugins/pwm_servo_m280.c
  plugins/rgb_led_m150.c
  plugins/rgb_led_strips.c
 )
 
-
 set(EMBROIDERY_SOURCE
  embroidery/embroidery.c
  embroidery/brother.c

main/my_machine.h

@@ -60,7 +60,7 @@
 //#define SPINDLE3_ENABLE         SPINDLE_NONE
 //#define SPINDLE_OFFSET          1 // Uncomment to enable settings for laser spindle XY-offset.
 // **********************
-//#define MODBUS_ENABLE           1 // Set to 1 for auto direction, 2 for direction signal on auxillary output pin.
+//#define MODBUS_ENABLE           1 // Set to 1 for auto direction, 2 for direction signal on auxiliary output pin.
 //#define WEBUI_ENABLE            3 // Enable ESP3D-WEBUI plugin along with networking and SD card plugins.
 //#define WEBUI_AUTH_ENABLE       1 // Enable ESP3D-WEBUI authentication.
 //#define WIFI_ENABLE             1 //
@@ -85,10 +85,13 @@
 //#define EEPROM_IS_FRAM          1 // Uncomment when EEPROM is enabled and chip is FRAM, this to remove write delay.
 #define ESTOP_ENABLE            0 // When enabled only real-time report requests will be executed when the reset pin is asserted.
                                     // NOTE: if left commented out the default setting is determined from COMPATIBILITY_LEVEL.
-//#define RGB_LED_ENABLE       2 // Set to 1 to enable strip length settings $536 and $537, set to 2 to also enable M150 LED strip control.
-//#define PWM_SERVO_ENABLE     1 // Enable PWM servo support, requires at least one PWM capable auxillary output.
-//#define BLTOUCH_ENABLE       1 // Enable BLTouch support. Requires and claims one PWM servo output.
-//#define EVENTOUT_ENABLE      1 // Enable binding events (triggers) to control auxillary outputs.
+//#define RGB_LED_ENABLE          2 // Set to 1 to enable strip length settings $536 and $537, set to 2 to also enable M150 LED strip control.
+//#define PWM_SERVO_ENABLE        1 // Enable M280 PWM servo support, requires at least one PWM capable auxiliary output.
+//#define BLTOUCH_ENABLE          1 // Enable M401/M402 BLTouch support. Requires and claims one auxiliary PWM servo output.
+//#define EVENTOUT_ENABLE         1 // Enable binding events (triggers) to control auxiliary outputs.
+//#define ESP_AT_ENABLE           1 // Enable support for Telnet communication via UART connected ESP32 running ESP-AT.
+//#define FEED_OVERRIDE_ENABLE    1 // Enable M200 feed override control.
+//#define HOMING_PULLOFF_ENABLE   1 // Enable per axis homing pulloff distance settings.
 
 // Optional control signals:
 // These will be assigned to aux input pins. Use the $pins command to check which pins are assigned.
@@ -118,7 +121,6 @@
 //#define Z_GANGED_LIM_MAX    1
 //
 
-
 #if WIFI_ENABLE || ETHERNET_ENABLE || WEBUI_ENABLE
 #define TELNET_ENABLE         1 // Telnet daemon - requires WiFi streaming enabled.
 //#define WEBSOCKET_ENABLE      1 // Websocket daemon - requires WiFi streaming enabled.