Skip to content

Run the Demonstration Remotely via Ethernet (AD7768)

Jump to bottom
nnaufel edited this page Nov 1, 2021 · 48 revisions

In addition to the DataStorm DAQ development kit running in standalone mode, it can also run while connected to computer remotely via an Ethernet cable.

Configuration for remote IIO Oscilloscope access via ethernet

The AD7768® Evaluation Platform in this configuration is comprised of the following components: The AD7768 Evaluation Platform in this configuration is comprised of the following components:

Configure BOOTSEL DIP Switches

Select the SD card as the boot source for the processor.



Configure FMC_VADJ DIP Switches

The FMC_VADJ power rails provide power to the EVAL-AD7768FMCZ via the FMC interface. This is an adjustable voltage. It must be set to 3.3V. Modify the VID_SW DIP switch settings to select 3.3V.

Assemble the Hardware

Follow the steps in the order shown below.

  • Insert the Micro SD card into the SD card slot
  • Insert the EVAL-AD7768FMCZ FMC connector into the FMC mating connector on the DataStorm DAQ board
  • Attach PC via ethernet cable
  • Attach the Micro USB cable
  • Connect the Signal Generator to the EVAL-AD7768FMCZ SMA connectors (channel 0)
  • Ensure that Jumper LK1 is in position B and LK2 is in position A on the EVAL-AD7768 board, for it to be powered via the FMC connector
  • Ensure that Jumpers SLP1 and SLP2 are in positions A (default) on the EVAL-AD7768 board
  • Connect the power supply to the DataStorm DAQ
  • Plug the AC-DC adapter into an AC outlet

Signal Source

A signal generator with 2 outputs is used to generate the differential signals driving the AD7768 inputs. The AD7768 expects the input signals to swing between AVSS and AVDD1 (+5V on the EVAL-AD7768 board). This means that the user is expected to provide a true differential input centered at VCOM (AVDD1-AVSS)/2 (as in yellow tag #5 below).

Install (if not already done) the Digilent WaveForms App.

Open the WaveForms App and Click on Wavegen in the left margin which opens a waveform widow

Click on Channels and select 2
Select Type as Sine
Select Frequency or Period
Set Amplitude to 2V
Set Offset (Common Mode Voltage) to 2.5V
For Channel 2, Match the Channel 1 settings
Select the Phase to 180 degrees for Inverse signal
Click Run All

Software for remote IIO Oscilloscope access via ethernet

There are a few software components that need to be installed in order to run this demo successfully:

  1. IIO Oscilloscope™
  2. A SW terminal like Tera Term VT or Putty

IIO Oscilloscope™

IIO Oscilloscope™ is a tool developed by Analog Devices. It can be downloaded for Windows or Linux from this web site: https://github.com/analogdevicesinc/iio-oscilloscope/releases (Download and install v0.13)

Define the host PC IP address

A wired ethernet point-to-point connection between the host PC and the embedded target is required. Use this link for instructions on how to assign a static IP address to the host Ethernet adapter. Set the following values

  • IP address : 192.168.0.1

  • Subnet mask : 255.255.255.0

  • No entries required for the other fields

Connect to the target terminal

  • A wired Micro USB serial port connection between the host PC and the embedded target is required
  • Launch a linux terminal (like Tera Term VT or Putty) and connect using serial port
  • Select 115200 baud
  • Select the appropriate target COM port

Define the target IP address

Type the following at the terminal prompt to set the target IP address

  • $ ifconfig eth0 192.168.0.2 up

Launch IIO Oscilloscope

Note: IIO Oscilloscope creates a .osc_profile.ini file in the Users/UserName/Appdata/Local directory. The next time IIO Oscilloscope is opened, the existence of this file delays connection to the target. It is recommended to delete the .osc_profile.ini (if it exists) prior to launching IIO Oscilloscope.

Connect to the target

  • Select the Discoverable/Scan option and click the Refresh button..
  • A successful connection results in discovery of the IIO devices. Press OK to continue.


Enable voltage0 ADC channel

Select a Plot Channel to be displayed in IIO Oscilloscope. Click on the check box in the Plot Channel window adjacent to voltage0. Right click on axi-ad7768-adc in the Plot Channels window. Select voltage0 and rising edge as the trigger parameters.


Capture Time Domain Signals

Press the Capture / Stop button to begin the capture process.


Capture Frequency Domain Signals with Frequency Markers enabled

Change the capture mode to Frequency Domain. Select an FFT Size and Average. Press the Capture / Stop button to begin the capture process.


Right click in the IIO Oscilloscope plot area. Select Single Tone markers. Press the Capture / Stop button to begin the capture process with markers.

Note the information in the Marker window. This capture shows a signal source of 10 khz with harmonic components.


Software for the Python demonstration

There are a few software components that need to be installed in order to run this demonstration successfully:

Install Python 3.7 (on Windows platform only)

  • Download Python 3.7 and run the installer

  • A typical installation location will be C:\Users\username\AppData\Local\Programs\Python

  • Edit the Windows System PATH environment variable to add the path to the Python directory

  • Edit the Windows System PATH environment variable to add the path to the Python\Scripts directory

Install PIP

  • For Linux platforms, use the relevant package managers to install python3 pip packages. For Debian-based distributions, follow this tutorial to install the same.
  • For Windows platforms, use the following instructions to install PIP

Install LibIIO - API library for IIO

  • For Linux platforms, follow this tutorial to directly install LibIIO dependencies on the host machine.
  • For Windows platforms, download and run the LibIIO installer from the GitHub releases page here

Install PyADI-IIO and matplotlib

  • Open a CMD shell.

      > pip install pyadi-iio
  > python -m pip install -U matplotlib

Download Python source code

  • Download the python source code from the github repository

  • Run the Python source code. Open a CMD shell

      $ python3 ad7768evb.py


This capture shows a signal source of 5 kHz with harmonic components.


Software for the C demonstration

There are a few software components that need to be installed in order to run this demonstration successfully:

Install GCC

  • For Windows machines, follow these instructions to install GCC on your windows machine
  • For Linux machines, run the relevant commands depending on distribution to install GCC and its related dependencies

Install LibIIO - API library for IIO

  • For Linux platforms, follow this tutorial to directly install LibIIO dependencies on the host machine.
  • For Windows platforms, download and run the LibIIO installer from the GitHub releases page here

Run the C programs

  • Download the C source code from the github repository

  • Compile the C source code (Use -liio flag to dynamically link the LibIIO libraries)

      $ gcc ad7768-iiostream.c -o ad7768-iiostream -liio


  • Run the C executable (use your relevant target IP address here)

      $ ./ad7768-iiostream ip:192.168.0.2


Software for the MATLAB demonstration

NOTE: This demonstration requires a licensed version of MATLAB and Simulink along with the Communication Toolbox installed.

There are a few software components that need to be installed in order to run this demonstration successfully:

Install MATLAB

Install LibIIO - API library for IIO

  • Download and run the LibIIO installer from the GitHub releases page here

Run MATLAB

  • Download the MATLAB source from the github repository

  • Open the Simulink model DAQ7768.slx file


  • Double click on the system object block of axi-ad7768-adc. Set your relevant target IP Address in the "IP Address".


  • Set your preferred stop time and run the simulation to see waveforms.

NOTE: Channels are arranged top-down with channels 0 to 3 on the left and channels 4 to 7 on the right.


This capture shows a signal source of 5 kHz in Channel 3 with harmonic components.


Shutting down the demo

  • Power down the target. Type the following at the terminal prompt

      $ poweroff

  • Wait until the linux terminal shows

      $ reboot : System Halted

  • Close out IIO Oscilloscope and all associated windows

Return to AD7768 Quick Start Guide

Please click Here to purchase platform boards

Arrow Data Storm DAQ Development Platform
  Introduction
  Developer Starter Guides
  Additional Developer Docs
  AD40xx Platform User Guide
  AD7768 Platform User Guide
  AD7768-1 Platform User Guide
  AD7606B Platform User Guide
  AD738x Platform User Guide
  AD469x Platform User Guide
  AD463x Platform User Guide
  ADRV9001/2 Platform User Guide

Purchase Platform Boards
Contact Us

Clone this wiki locally